Re: My winter project
1 Attachment(s)
If those seals ever come loose, this will do the trick. Much stronger than the regular 3m stuff.
|
Re: My winter project
Thanks, Jim.
|
Re: My winter project
Tom I used the 3M, and seems to stick good but I had it everywhere. I will give that a shot if I have problems.
|
Re: My winter project
5 Attachment(s)
Fitting the carpet and cutting holes has taken a lot of time.
|
Re: My winter project
Awesome work
|
Re: My winter project
Gonna have this puppy ready for the national show in Salt Lake at end of June?
|
Re: My winter project
1 Attachment(s)
Quote:
|
Re: My winter project
3 Attachment(s)
I got the heat stove on, sometimes just little details.
|
Re: My winter project
Great job, I always enjoy watching your attention to detail
|
Re: My winter project
5 Attachment(s)
Quote:
|
Re: My winter project
2 Attachment(s)
Another one.
|
Re: My winter project
Chrome paint looks pretty good in the pictures!
|
Re: My winter project
5 Attachment(s)
Very small update: bodywork stuff so it takes me a long time. I did get epoxy on.
|
Re: My winter project
3 Attachment(s)
Few more.
|
Re: My winter project
4 Attachment(s)
I started setting some trim pieces in place, all the original holes were welded so should drill new holes or try the adhesive clips? I have read some stuff about the stick-on kind but has anyone had luck with them?
Thanks guys. |
Re: My winter project
5 Attachment(s)
I have been working on my wing windows. I'm pleased with how it went with the new seals.
|
Re: My winter project
Quote:
|
Re: My winter project
I think the 3m VHB double sided tape is what you need. Have you restored any trim? Any ideas how to get dents out etc....
|
Re: My winter project
That anodized aluminum trim is a huge PITA to restore. It get cloudy with exposure, dent and scratches easily. About the only restoration you can do with them is apply new woodgrain tape to them and repaint the black if they are otherwise nice. I have seen guys strip the anodizing off, then polish the aluminum to a high shine. Without the anodizing in place, the trim will dull easily just with the ambient humidity.
Fortunately, there are a lot of NOS trim out there for most of the sections. The hardest ones are the Blazer specific forward quarter panel pieces. Mar-K makes good repro trim if you can't locate NOS. As for the retention of these, I would stick with the OEM steel clips, either the threaded or push in variety depending on location. Some locations on the trim used the plastic adhesive clips, mostly in the middle of the longer side trim such as the door and quarter panel pieces. |
Re: My winter project
Quote:
Quote:
Quote:
|
Re: My winter project
4 Attachment(s)
Well, I've been putting off the door repairs, finished welding the cracked hinge area and the screw holes I will get the filler going.
|
Re: My winter project
Quote:
Looks great! I wish I was better at body work. I would have saved myself a fortune. I read about your dilemma on the side trim. I went to ebay and purchased extra plastic adhesive pieces, and I ordered some more small black screws that match the original screws. I plan on going the adhesive tape/screw route at this point. Although, since you are still in body work, you could make some Cardboard or Construction paper templates of the trim with the holes marked on the paper & drill them like that? They would be easy to tape to the body & line up. Have a good day, looking forward to the next update! |
Re: My winter project
Quote:
|
Re: My winter project
1 Attachment(s)
Quote:
|
Re: My winter project
3 Attachment(s)
I started the filler and sanding.
|
All times are GMT -4. The time now is 08:09 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com