Re: Project...praise the lowered
Quote:
|
Re: Project...praise the lowered
Quote:
|
Re: Project...praise the lowered
quick update.last box side ready for primer.hood almost ready.rad support mounts are fabbed and ready to be welded to the frame,rad support is now modified to run my wires/lines/power steering cooler and mounts for the over flow are in place.also primed and painted the rad support,inner fenders top and bottom.front clip is ready to go in place for good.im slowing picking the list off one job at a time.its getting smaller by the day.
|
Re: Project...praise the lowered
Quote:
|
Re: Project...praise the lowered
still at it.the last little while i extended the wiring harness for the head lights,blinkers,driving light and sensors..so i could run the last of the wiring into the fire wall.got the block mounted to the main panel.then started to hook the 67 headlights up to the newer wiring harness.i got the rad support and inner fenders mounted for the last time.over flow bucket and rad in place and hooked up.power steering cooler now mounted in place,brackets made for the billet grill,inner roof and wind shield post painted with speckle paint.looks great in person.i ran into a bit of a problem with my dome light.the lense is nowhere to be found.so as a quick solution i did some hacking and made the dome light from the new sierra fit in its place.looks slick.also i have a new electric fan on order.im sure im forgetting more but thats it for now.
http://i932.photobucket.com/albums/a...y/IMG_2053.jpg http://i932.photobucket.com/albums/a...y/IMG_2055.jpg http://i932.photobucket.com/albums/a...y/IMG_2156.jpg http://i932.photobucket.com/albums/a...y/IMG_2157.jpg http://i932.photobucket.com/albums/a...y/IMG_2154.jpg http://i932.photobucket.com/albums/a...y/IMG_2155.jpg |
Re: Project...praise the lowered
The speckle paint is a cool idea...and the dome light looks like it fits well!
|
Re: Project...praise the lowered
lookin good, looks really clean and the dome light is a subtle upgrade
|
Re: Project...praise the lowered
read most of the pages and looked at all the pictures you have one very nice and i mean very nice most likely the cleanest truck i have seen so far great job on the truck i am definately sticking around for this one
|
Re: Project...praise the lowered
the speckle paint gave it a nice finished look.laid down a black base then it only took one can to cover.the dome light might have taken 10 mins tops.all i did was trimmed about 1/4 inch on the top and bottom of the opening then notched out both ends for the mounting tabs.it was quite easy.
|
Re: Project...praise the lowered
Quote:
|
Re: Project...praise the lowered
The speckle paint looks awesome! In the pics, it almost looks like felt or carpet! I may have to steal your idea! :lol: Keep up the good work!
|
Re: Project...praise the lowered
Quote:
|
Re: Project...praise the lowered
i got a little more done this weekend.rear bag mounts completely welded,c notches completely welded,and all the suspension stuff in the rear painted with box liner.then i got the rear bags hooked up,pan hard bar installed,made a cool large grommet for the firewall where the front clip wiring goes through.and tonight i was able to get my wheels on,hook up the valves and made the whole truck go up and down a few times.good to finally be at that stage.because i had to raise the body up a little more then what i planned,it doesnt quite sit on the rockers but its pretty close
http://i932.photobucket.com/albums/a...y/IMG_2228.jpg http://i932.photobucket.com/albums/a...y/IMG_2224.jpg http://i932.photobucket.com/albums/a...y/IMG_2229.jpg http://i932.photobucket.com/albums/a...y/IMG_2226.jpg http://i932.photobucket.com/albums/a...y/IMG_2225.jpg |
Re: Project...praise the lowered
looks good man. What made you raise your body from where you wanted it? Any pics of the rear section?
|
Re: Project...praise the lowered
im back in action.after so many things holding me back from working on the ol girl i finally got some things done.hood is now in high build ready to be blocked,today i painted the drive shaft,installed new u joints and installed the shaft,installed all new emergency brake cables,e brake shoes,axle brake lines,rear calipers with pads,rear rotors,front rotors,and front calipers with pads.in the end the hand brake worked out perfect.i should have some pics tomorrow.
|
Re: Project...praise the lowered
Progress! Good. I was getting ready to go through withdrawels! :lol: Pics are always good on here!
|
Re: Project...praise the lowered
that truck had a lot of rust and you brought it back to life , one word for you bud,
!!!! amazing !!!! |
Re: Project...praise the lowered
Quote:
|
Re: Project...praise the lowered
Quote:
|
Re: Project...praise the lowered
no pics today guys.i just spent from lunch time until dark trying to bleed the stupid f*#^in abs brake system.man its frustrating.im to the point now of just ditching the abs unit.i can pressure the rear brakes for bleeding but cant get any pressure for the fronts.i tried everything.i think its losing pressure inside the abs unit.any one have any ideas? keep in mind the system is from the 01 sierra i used a a donor truck.and it was completely drained for sand blasting and paint.also all new lines.any one?
|
Re: Project...praise the lowered
sorry bro, no clue, but now i know I am ditching the abs I was going to use.......
|
Re: Project...praise the lowered
Maybe a new ABS unit? Have you tried backwards bleeding the system?
|
Re: Project...praise the lowered
i have had this happen before with gm abs brakes. Usually i open all the bleeders and leave the cap off the master cylinder for 30 minutes to an hour. Keep an eye on it so it does not run out of fluid. After that i close everything up and have someone pump the brake real slow and steady until there is some pedal the bleed each wheel normally just pump the brake slow each time. If you push the pedal fast or there is a bubble in the abs block it closes a valve in the abs block.
|
Re: Project...praise the lowered
wow! just found this and read through the entire thing, what an awesome build! keep it up man, its incredible!
|
Re: Project...praise the lowered
Quote:
|
All times are GMT -4. The time now is 09:49 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com