Re: So 1 more 72 blazer going under the knife
 

Do you happen to have rear hatch lock and mechanisms thanks

Re: So 1 more 72 blazer going under the knife
 

Would you happen to still have the passenger side "B" pillar. I was trying to put a quarter on mine and found that it was T-boned on one time or another.
Mark

Re: So 1 more 72 blazer going under the knife
 

I may I'll look tomorrow and let you know.

Re: So 1 more 72 blazer going under the knife
 

Tailgate weatherstrip retainers still there?

Re: So 1 more 72 blazer going under the knife
 

Sorry, I have the very back piece that holds the tail lights.

Re: So 1 more 72 blazer going under the knife
 

I found the b-pillars I thought I had just looked in the wrong place. Let me know if you still need them and I'll get you a picture.

Re: So 1 more 72 blazer going under the knife
 

What about a rear license plate bracket or brake light harness? Also need a dome light assembly if Blazers have one.. I believe all would fit 67 fleet side, but feel free to advise if not!

Shipping to 90094. Thanks!

Re: So 1 more 72 blazer going under the knife
 

I'll look tomorrow and let you know.

Re: So 1 more 72 blazer going under the knife
 

Thanks!

Re: So 1 more 72 blazer going under the knife
 

Sorry no rear license plate bracket or brake harness. 72 single wall tops had a dome light but if you don't have a single wall you are good. 72s could also have under dash lights so depends on what year you're working on. I had a 71 with underdash lights but not sure if someone installed it or it came that way. I do have single dome lights and underdash harnesses.

Re: So 1 more 72 blazer going under the knife
 

Here are the dome lights on a 72 for reference.

Re: So 1 more 72 blazer going under the knife
 

haven’t gone through all 14 pages but what’s up with rear seat floor mounts. Top of bed and bottom brace ?

Re: So 1 more 72 blazer going under the knife
 

No rear seat channel may have the front mounts for the rear seat. Quarters are gone but have a small section of another blazer, how long a piece do you need. I'm assuming a floor brace, I have another floor setting here which brace do you need.

Re: So 1 more 72 blazer going under the knife
 

The brace wheel well to wheel well on bottom for mounting rear seat. And the front mounts on the top side. The flat ones with captured nut for seat mount (my blazer was not optioned for rear seat )

Re: So 1 more 72 blazer going under the knife
 

I have the top side and possible the nuts for underneath on the front side. I'll look tomorrow and let you know.

Re: So 1 more 72 blazer going under the knife
 

Here is what I have for the rear seat, its everything you will need to mount the front of the rear seat other than the 7/16 fine thread bolts. The rear of the seat uses 1/2 coarse thread just an fyi. 59 shipped in a small flat rate box.

Re: So 1 more 72 blazer going under the knife
 

how about a front driveshaft? my truck is a 72 blazer 350/350/205. shipping to 53140. thanks

Re: So 1 more 72 blazer going under the knife
 

I'll look tomorrow and let you know but I should.

Re: So 1 more 72 blazer going under the knife
 

Looks like 34 shipping and 60 for the drive shaft.

Re: So 1 more 72 blazer going under the knife
 

Long shot but do still have shifter parts in post#291? I don't need the shift rod just the piece it is attached to (bellcrank)

Re: So 1 more 72 blazer going under the knife
 

I'll have to look and let you know.

Re: So 1 more 72 blazer going under the knife
 

Hi, How about the glove box lid and ashtray? Passenger side seat belt retractor? Thanks

Re: So 1 more 72 blazer going under the knife
 

Thanks for looking. I came up with something that will work.

Re: So 1 more 72 blazer going under the knife
 

I forgot to post pictures, here is what I have.

Re: So 1 more 72 blazer going under the knife
 

Dwayne, Do you have one of these from the door jamb ?