|
Re: Orson the 49 GMC ~ Chris C.
3 Attachment(s)
We have installed the fuse box
We began to wire the body harness And the speaker box design was finalized today, Monday they head to the plasma cutter. |
Re: Orson the 49 GMC ~ Chris C.
4 Attachment(s)
Today we got the steering column in primer, wet sand and paint tomorrow.
The headlight and turn signals are all wired |
Re: Orson the 49 GMC ~ Chris C.
3 Attachment(s)
The new PCM arrived and we installed it, still no spark. This harness is junk. When you Connect the battery there is no voltage to the PCM relay or any of the fuses! And of course I am unable to contact the seller. $260 wasted! I’ll have to buy another one!
|
Re: Orson the 49 GMC ~ Chris C.
4 Attachment(s)
We got the steering column in paint today
We spent more time cutting out and replacing Michael's shotty work We created and fit the Transmission tunnel We even wired and installed those expensive turn signals |
Re: Orson the 49 GMC ~ Chris C.
who's harness did you get?
|
Re: Orson the 49 GMC ~ Chris C.
EZ wiring
|
Re: Orson the 49 GMC ~ Chris C.
I went with a painless wiring harness.
|
Re: Orson the 49 GMC ~ Chris C.
Painless is nice, but rich for my blood. I paid $150 for the EZ
|
Re: Orson the 49 GMC ~ Chris C.
4 Attachment(s)
We accomplished a lot today...
The body harness in the engine bay is all finished up |
Re: Orson the 49 GMC ~ Chris C.
4 Attachment(s)
The old engine harness is remove
the tail section is now all attached to the frame |
Re: Orson the 49 GMC ~ Chris C.
1 Attachment(s)
And the column is finally finished!
|
Re: Orson the 49 GMC ~ Chris C.
Good progress, thanks for sharing.
|
Re: Orson the 49 GMC ~ Chris C.
You bet! The goal is that more folks are undaunted!
|
Re: Orson the 49 GMC ~ Chris C.
4 Attachment(s)
We got the dash all finished and painted.
|
Re: Orson the 49 GMC ~ Chris C.
2 Attachment(s)
in paint
|
Re: Orson the 49 GMC ~ Chris C.
pretty stuff!
|
Re: Orson the 49 GMC ~ Chris C.
5 Attachment(s)
Thanks!
Today’s progress, we wired the ignition. The new engine harness came in, so that will be going in in the next few days (hopefully then it’ll be a runner) we continue to work on that dash (it still doesn’t meet my standard) the dash is holding everything up The back wall of the cab goes into final paint tomorrow |
Re: Orson the 49 GMC ~ Chris C.
5 Attachment(s)
Still working on that dash
This is how we create the hidden stereo Here it is mocked up And I’ve decided to put a 2 USB power adapter behind the ashtray |
Re: Orson the 49 GMC ~ Chris C.
2 Attachment(s)
These are the side panels for your 6.5” kick panel speakers
And the back of the cab in final paint! |
Re: Orson the 49 GMC ~ Chris C.
Nice work on the truck and I've been following the build. My question is once you mount the hidden stereo in that plate you made, is it going to leave enough room for your wiper motor?
|
Re: Orson the 49 GMC ~ Chris C.
yup, I’ve done it many times before
|
Re: Orson the 49 GMC ~ Chris C.
2 Attachment(s)
We spent all day fitting the front bumper, not quite done. Will finish tomorrow and move on to the rear bumper.
Switched sides on the brackets to tuck it up and removed 3 inches from the brackets |
Re: Orson the 49 GMC ~ Chris C.
4 Attachment(s)
We finalized the front bumpers Position and made the brackets
|
Re: Orson the 49 GMC ~ Chris C.
3 Attachment(s)
We welded them on and leveled and installed the bumper
We then mocked up and got 2/3 of the way done with the rear brackets |
Re: Orson the 49 GMC ~ Chris C.
2 Attachment(s)
Here’s some more
|
| All times are GMT -4. The time now is 12:17 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com