Re: Yet another GMC build
1 Attachment(s)
Old frame out. New one shoved in. Everything I could find said that a 58-59 frame is the same but front frame rails need to be shortened and bumper bracket holes redrilled. I found my core support holes don’t line up by 3/4 to 1 inch. Since they are riveted, removing the frame brackets and relocating them will be super fun. That was sarcasm. I was hoping to have that booger bolted tight today. On a side note, I think you can actually see how warped my front frame rails were in the photo.
|
Re: Yet another GMC build
Quote:
if distance from the body mount, you can probably find that much just by loosening everything and biasing the cab to the chassis, the fenders to the core support, core to frame, etc. if width, can you just add a plate to the core support? |
Re: Yet another GMC build
Quote:
|
Re: Yet another GMC build
Could also try to tilt the core and trim the back of the splash pan to fit. Will investigate more
|
Re: Yet another GMC build
What's that front crossmember in the old frame out of? That thing looks huge.
|
Re: Yet another GMC build
Quote:
|
Re: Yet another GMC build
look in here for frame dimension drawings. the 58-59 frames are longer out front and the rad support brackets are in a different location. it's all ahead of the spring mounts so from there back they are the same.
https://www.trifive.com/d1/55-59Assy.pdf |
Re: Yet another GMC build
frame dimension drawings start in section 2 sheet 24. you are looking for sheet 33. a lot of the dimensions are given off the imaginary face of the cab line (firewall) so you may have to look closely to find the place where the rad support brackets are measured from. kinda looks like the center line of a cross member at the rear of the cab and takes a couple of dimensions to add up for the total dimension.
anyway, you'll figure it out. |
Re: Yet another GMC build
1 Attachment(s)
I ended up knocking out the rivets and moving the brackets back about 1”. Since it was kind of hard to access to drill new holes I just welded the brackets to the frame. Cab is bolted solid to the frame now. Got in the gas tank, battery drop box, and cleaned and painted the Dana 44 so should be able to start reinstalling suspension.
|
Re: Yet another GMC build
good solution!
|
Re: Yet another GMC build
2 Attachment(s)
So far so good. Still figuring out the firewall. Will either be homemade or a wheelbarrow. Deepest “big block” firewall is 4” recessed and I need 6”. Will have to move the gas pedal over, and the brake pedal. Vintage air unit may not fit right anymore. Plenty of obstacles that I’m sure have grand solutions. Just need to stare at it long enough and drink more coffee.
|
Re: Yet another GMC build
That looks like a lot of engine set back
|
Re: Yet another GMC build
Quote:
|
Re: Yet another GMC build
Quote:
|
Re: Yet another GMC build
holy mid-engine batman!
the Cummins needed a 6" doghouse too, but wasn't that wide. while a wheelbarrow would be sweet, i'd be more worried about keeping the doghouse as narrow as possible. |
Re: Yet another GMC build
I recommend to sit in the cab area and place your feet where the pedals would be. Nothing worse than a cramped accel pedal on a long ride and you need room for your foot to access the brake pedal easily. Try to make the firewall recess as narrow as possible. Maybe even a removable cover like a van has. Also think of shape if you plan on upholstering it. If a wheelbarrow is the shape you like but too wide, you could split it and seam down the middle. If going with sheet metal from scratch, mock it up with posterboard or even wood veneer and tape.
|
Re: Yet another GMC build
Im seeing what you guys are saying. The width is more of an issue on this narrow cab than it would be on a c10. To get this to work I’ll have to relocate the gas pedal and therefore the brake pedal. It interferes with the brake booster bracket and might as well scoot the column and gauges. I have 4” of room to move the seat over, too. And new carpet. Plus my vintage air won’t fit but it looks like an Old Air Hurricane will. Im just being stubborn about making it work. Truck was a great driver but could never turn corners despite the c4 suspension.
|
Re: Yet another GMC build
3 Attachment(s)
Inspiration.
|
Re: Yet another GMC build
What truck is at the bottom, with the interior shot?
|
Re: Yet another GMC build
1 Attachment(s)
Quote:
|
Re: Yet another GMC build
2 Attachment(s)
Wheelbarrow seems to work. I like that it’s curved. Anything I could’ve made would be all sharp angles. Going to recycle the hump from the firewall as the transmission bump. Then on to relocation of pretty much everything else in the cab.
|
Re: Yet another GMC build
Looks nice. Love the set back
|
Re: Yet another GMC build
Quote:
|
Re: Yet another GMC build
1 Attachment(s)
The gas pedal is pretty much where the brake used to be. I had to move the booster bracket over a couple inches. By grinding the welds on the brake pedal arm, I can now move it to the other side of the swing arm shaft. I put a seat back in and the gas pedal feels comfortable where it’s at but I think the brake pedal is going to be a left foot operation. Driving with both feet doesn’t really bother me any more than using a clutch. I’m just going to leave the column and seat locations alone.
|
Re: Yet another GMC build
That would drive me crazy, but, to each their own.
Is there room for your left foot anywhere when not being used for the brakes? Have you checked local laws for foot and pedal clearance laws, if any exist? Wouldn't wanna find out AFTER doing all that work. |
All times are GMT -4. The time now is 05:33 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com