Re: What did you do to your truck today? Chapter II
 

Took my console apart and took it to a place to get it media blasted.

Re: What did you do to your truck today? Chapter II
 

http://i1183.photobucket.com/albums/...D351CEAF0D.jpg


Excuse the dirty interior but can't get over how bright my dome light is.. fellow board member made it for me ( same guy who makes the full led tailights) can't remember his screen name

Re: What did you do to your truck today? Chapter II
 

well for the last two days been going through motor plastic gauged all the bearings , wire wheel , wire wheel , paint stripper , wire wheel , wire wheel , oh and did I mention wire wheel . it almost looks like new cast in most places . the stripper really helps take the caked on baked on grease along with the old paint . it came from a 1 ton cube van with 76 thousand on it super clean inside super filthy outside . four bolt main haven't run the head numbers yet guessing nothing great but I did drive it before I yanked the engine seemed to be pretty snappy in that huge tank so should be good in my c10 . oh and I ran a tap down every hole I could find with a thread in it I use old bolts in the holes to seal em from the paint but takem out before the paint dries so I don't pull paint chunks when it dries

Used Engines
 

VERY NICE ! .

I used to do this when I was building used cars & trucks for re sale .

Re: What did you do to your truck today? Chapter II
 

Pulled the dash pad last night. It's been sitting under towels, and until today hasn't been cleaned in I don't know, 20 years maybe. Real happy with it. The vinyl in these trucks are well made. Out of the elements and they're built to last. Now it's off to bed. I'll see this again in 18 months-ish

https://scontent-sjc2-1.xx.fbcdn.net...fa&oe=593DE2F8

https://scontent-sjc2-1.xx.fbcdn.net...86&oe=5903D134

Don't imagine there's a clean fix?
https://scontent-sjc2-1.xx.fbcdn.net...56&oe=58FD9486

https://scontent-sjc2-1.xx.fbcdn.net...2e&oe=5936A29D

Re: What did you do to your truck today? Chapter II
 

As I previously posted I took my console for media blasting yesterday and got it back today. I am not comfy leaving near impossible to find parts out of my control for any longer than I have too.

Re: What did you do to your truck today? Chapter II
 

I know that feeling! I try not to either but sometimes you just gotta!:chevy:

Re: What did you do to your truck today? Chapter II
 

X3............Thing I sweat most is my hardware. Luckily I found a zinc plating operation in Reno/Sparks. I might prefer phosphate, but I'm not prepared to leave this stuff longer than a day or two, and no shipping either.

Re: What did you do to your truck today? Chapter II
 

15x 8 Blazer rims blasted and painted. Getting there....

Re: What did you do to your truck today? Chapter II
 

Finally after 6 plus years I got up off my dong and fixed the heater, MAN why did I wait for so long...lazy on some stuff.

Never Pop kit is awesome, went together smoothly with minor mods. Some mini stainless allen head machine nylocs for the specialty screws that stripped out and presto chango....

Here ya go...gotta put the tach back in...more to come. The blower motor resistor went out years ago that got replaced also...simple.

Re: What did you do to your truck today? Chapter II
 

Lookin' good DaveK and toolbox. Dave what color is that? spray gun or can? Thanks brothers.

Re: What did you do to your truck today? Chapter II
 

It's an antique white and with a gun. Kinda re-thinking it though. They're not as yellow as in the picture but not the stock white I think they should be so will probably rough up the outer part and re-shoot before mounting tires.

Re: What did you do to your truck today? Chapter II
 

Proud of this... super nice longbed floor no one wanted, I think I ended up getting it for like $150, cut into a shorty, and the bedside fit like a glove!

Re: What did you do to your truck today? Chapter II
 

got it in color man its all shiny and new lookin makes ya want to stay and start putting all the shiny bits of chrome and aluminum on . ill wait one more day I guess

Re: What did you do to your truck today? Chapter II
 

12 months in the making, installed today

Re: What did you do to your truck today? Chapter II
 

didn't get far today weather is crazy had to snow blow the drive too many times but got the new timing chain and cover on fuel pump balancer and most of the spark plug heat shields

Re: What did you do to your truck today? Chapter II
 

I made a very small amount of progress on disassembling my bed. I used a sawzall to cut off the last 2 bolts holding the front panel on. I couldn't get the sawzall in a good spot to cut any of the bolts holding the bedsides on, so I picked up a couple of cutoff wheels. But, I ran out of daylight.

Re: What did you do to your truck today? Chapter II
 

Have this to deal with today, not a bad thing. These 2 cracked ones got me through over 1 1/2 years. Last time I dealt with the same issue it broke immediately.

Will post up some pics when done. I had some used manifolds on hand from a board member and thought about going a number of different routes, yet ended up being convinced after getting over 10 years of service out of the old system I would be money wise to do the same again.

Re: What did you do to your truck today? Chapter II
 

Yesterday, I found out why everyone hates aftermarket patch panels. I had to slice this thing open in two places to fit the original fender lines.

http://67-72chevytrucks.com/vboard/a...1&d=1486948251

Re: What did you do to your truck today? Chapter II
 

That would be why we are metal men. I have a lot of that to look forward too.

Re: What did you do to your truck today? Chapter II
 

Yeah, it's a beautiful fender that's only had one repaint. Perfectly straight. The only bondo was to hide what was left of the lower cup. There's a couple pinholes at the back, but once done, WAY better than an aftermarket fender :)

I just didn't expect it to fit that bad. It was a key parts one too. I think they want you to use the whole thing, it probably matches a lot closer at the top, I wanted to keep as much of the original lip around the fender as possible as the patch one didn't look to be formed all that great.

http://67-72chevytrucks.com/vboard/a...1&d=1486360744

Re: What did you do to your truck today? Chapter II
 

Day 2 of ordering parts form various suppliers in the USA. I'm having parts shipped to Plentywood Montana and will be going in early March to get them.

Re: What did you do to your truck today? Chapter II
 

Cleaned and repainted the alternator using Eastwood rattle cans. I don't know if it would work at a concours show but looks alot better then when I took off the truck. I guess you could call it minor detailing.:chevy::chevy:Attachment 1622258

Attachment 1622259

Attachment 1622260

Re: What did you do to your truck today? Chapter II
 

Finished the install of the new Radiator, electric fan and hose up grade. Too much??

Re: What did you do to your truck today? Chapter II
 

wow looks like a jewelry box Mator.