Re: 52 GMC Envoy Burb meld/build
The Envoy is full BOXED frame. Heavier duty than the 52. I will consider using the stock inner quarters from the Envoy. Still working on the measurements. As far as the floor saggin, with the full frame and 'crash tested' floor, I think its stronger than the original wood floor of the burb--but thanks, I will keep that in mind. Gotta love this site and forum!
|
Re: 52 GMC Envoy Burb meld/build
What is the general width of this "Envoy" Dash Board? Rocker to rocker? What is your thought about "Envoy's Firewall to Burb's windsheild."
|
Re: 52 GMC Envoy Burb meld/build
Quote:
For the height I might have to section the firewall slightly. Nearest the Envoy windshield is the same height as the burb, however its about 6 inches further forward. Where the 52 windshield will sit the Envoy is about 5 inches higher, so the front edge can go under the hood. I'll post pics of how I figure that one out! Lot of thoughts at this point. I sure appreciate all the input. |
Re: 52 GMC Envoy Burb meld/build
subscribed love it when people think out of the box probably cause it is my way of thinking
|
Re: 52 GMC Envoy Burb meld/build
you are right on the boxed frame, i forgot about that, duh. my mistake. it will be an easy job then.
|
Re: 52 GMC Envoy Burb meld/build
Quote:
|
Re: 52 GMC Envoy Burb meld/build
:lol: what an awesome project. subscribed.
|
Re: 52 GMC Envoy Burb meld/build
:lol: what an awesome project. subscribed.
|
Re: 52 GMC Envoy Burb meld/build
Vote of confidence of course. I know u can do it. if i were closer i would love to come over and help, i love doing jobs like that, hat is what makes me tick, the higher the dificulty the better the job.
|
Re: 52 GMC Envoy Burb meld/build
This looks like it is going to be interesting. Add me to the list of those who subscribed to the thread.
|
Re: 52 GMC Envoy Burb meld/build
The BODY of the BURB is coming off this weekend and next!!!!:metal:
|
Re: 52 GMC Envoy Burb meld/build
Can wait to see some action shots of the body swap!
|
Re: 52 GMC Envoy Burb meld/build
It will work just fine with your gas ax and your blue tip wrench !!
|
Re: 52 GMC Envoy Burb meld/build
Don't forget the 5 lb sledge!
|
Re: 52 GMC Envoy Burb meld/build
Quote:
|
Re: 52 GMC Envoy Burb meld/build
Sounds like a fun project.
|
Re: 52 GMC Envoy Burb meld/build
Two steps, unbolt, pull hard.
|
Re: 52 GMC Envoy Burb meld/build
2 Attachment(s)
Burb body headed for buddys shop!! Envoy headed there on Saturday!!:bann:
|
Re: 52 GMC Envoy Burb meld/build
Another subscriber!!
|
Re: 52 GMC Envoy Burb meld/build
This is gonna be cool..
|
Re: 52 GMC Envoy Burb meld/build
Watching this build for sure ! Can I get a shot of the door lettering on your
52 ? Thinking about adding lettering to my 49. |
Re: 52 GMC Envoy Burb meld/build
4 Attachment(s)
Can't read it anymore. It was a Lincoln County Search & Rescue unit in eastern Washington. Still have the siren, gurney, factory dash plate, etc. The third pic I'm going to copy from my backyard service station set-up to my 67 c/10
|
Re: 52 GMC Envoy Burb meld/build
2 Attachment(s)
The 67
|
Re: 52 GMC Envoy Burb meld/build
Gotta watch this one!!!!
|
Re: 52 GMC Envoy Burb meld/build
Quote:
|
All times are GMT -4. The time now is 06:36 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com