Re: My 69 lonbed
 

Looking good! I'm really wanting to shave my firewall and run vintage air but the budget isn't looking good for that for me :lol:

Re: My 69 lonbed
 

it didn't cost really anything to shave the firewall just steel. im unsure of the cost of the vintage air w/ ac. the smoothed out firewall outweighs the cost of the vintage air unit for me. there will be tons more work on the firewall to come! i plan to box in the channel where the original engine wiring ran, plus some surface rust on the driver side. only a little at a time!

Re: My 69 lonbed
 

Other than the fact that you cut the top hump down is this the look you're going for? If I do shave my firewall I'm going all the way with this look including relocating the booster to the frame or under the dash....so it'll cost me about 2G to do between Vintage air and the frame mounted booster setup and pulleys for the A/C, etc....

But it looks SOOOOOOO sweet!!!! (Especially with the LSX like in this picture)
http://i97.photobucket.com/albums/l2...o/100_5147.jpg

Re: My 69 lonbed
 

speachless... ha ha yeah thats it! i've never seen where the booster is relocated on 67-72 c10

Re: My 69 lonbed
 

Scotts hot rods makes frame mounted and under dash mounted setups. I've read of clearance issues with both....frame mount with exhaust and under dash mount with wiper motors.....one thing always leads to another :lol:

Are you going to smooth your cowl like in the above picture?

Re: My 69 lonbed
 

i was thinking about it. im going to close off the fresh air vents in the cab so more than likely yeah. i'm going to keep my wind wings and i'll have ac so no worrys. it's been countless times when im driving down the freeway open the fresh air vents and get suffocated with dust, leaves and what ever else gets in through the cal. **** sucks! ha ha. i was going to do 1 peice windows but then i found out you have to hack your door. plus with the 1 piece rubber it looks funny because it kicks out where the wind wing was. to me when the trucks laid out on frame wind wings out and its a longbed... looks tits

Re: My 69 lonbed
 

this is all i accomplished today. but something is better than nothing and it's gotta get done anyway. i plan to put a posi 5 on 5 axles and 3:73 ratio i need all of that. if you have parts let me know! even A complete rear end i need the 5 on 5 though
:fb:
Attachment 491974

Attachment 491975

Re: My 69 lonbed
 

love the progress, great looking truck!!

Re: My 69 lonbed
 

Awesome! Long and low...

Re: My 69 lonbed
 

Thanks! do you have a thread for either of your trucks?

Re: My 69 lonbed
 

Do you mean build thread? If so no i dont because well, i havent really done any mods to them. I got them both the way they are. Plans for the '70 are an air ride kit from ridetech, foose nitrous or nitrousII wheels, and a system. The '72 4x4 is just my daily driver. Plans are to make it a swb, repair rust, slap some paint on, maybe later down the road stick a vortec in it. Hopefully ill have enough money by this winter to start on the '72 and have a build thread. Untill then, i just sit and watch, wishing i had the some money and time, not to mention the skills you guys have!

Re: My 69 lonbed
 

yeah i was unsure if you had a build thread or not. both trucks look great. im not so sure about the tail lights on the one though... any plans for those?

Re: My 69 lonbed
 

I kinda like them, they had stupid plastic covers on them, so i took those off. They are from an '83 s-10, they sure do get a lot of comments though!

Re: My 69 lonbed
 

I like your progess so far... You gonna keep it orange? I'm partial to orange on black '69s
http://photos-e.ak.fbcdn.net/hphotos..._2317952_n.jpg

Re: My 69 lonbed
 

thanks, im gonna have it primer and build it up first. drive it and get all the bugs out. tear it down and go with some kind of electric blue

Re: My 69 lonbed
 

Oh but blue is so common... How many properly orange trucks do you see? :lol:

Plus if you ever got in an accident, and the other guy says "I didn't see him coming", you can call total bull****.

Re: My 69 lonbed
 

very good point (there are tons of blues out there on vehicles so if its going to be blue make it a custom one so it stands out) that is what i would do:lol:

Re: My 69 lonbed
 

beautiful truck...
Can u give me sum more info on what i can do to get the lowest
possible stance while still using stock suspension for the
time being thanks for your info

Re: My 69 lonbed
 

Here is a url for the notch
http://www.brotherstrucks.com/prodin...number=CNK6372

here is the url for the drop blocks
http://www.brotherstrucks.com/prodin...number=LBU6372

for the front you can buy 2.5" drop spindles but your front cross member will limit you. basically your front cross member will sit on the ground not allowing you to go lower. many companys make spindles so they shouldn't be hard to find. they also make an aftermarket front cross member that will let you lay frame (the route im going) if your not running air bags you shouldn't have any problems with the spindles and will give you a nice stance. these spindles can be used with your factory control arms or aftermarket
let me know if you need any more help/info

Re: My 69 lonbed
 

nice truck you got there so far, here is a pic of mine with the booster moved. in the future i still have to shave the other side of the firewall yet to mount my vintage air, but i had to see some color on her for a bit.

Re: My 69 lonbed
 

so here is my rusty frame
Attachment 494286

Attachment 494287
sand blasted the ramaining front half and primed
Attachment 494288

Attachment 494290
im not using any of this but for now to move it around easier...
Attachment 494291

Re: My 69 lonbed
 

bye bye drum
Attachment 494293
this was way dirty!

Attachment 494294
its starting to look like something!
Attachment 494295
see how the frame doesn't lay. thats a problem ha ha
Attachment 494296
it felt good to throw all this away but it sucks to think i have to replace it all... disc brakes and power rack

Attachment 494297

Re: My 69 lonbed
 

Great progress. I thought you had mentioned a dropmember for the front....are you changing plans and sectioning the crossmember now or did you just bolt that up for the picture?

Re: My 69 lonbed
 

here are my valves i'll be using these were almost 500 bucks!
Attachment 494299

Re: My 69 lonbed
 

yeah most definately using the drop member but when i move my frame around at the shop i need to lift the frame in the back with a forklift while putting a strap from the front of my frame back to the forklift. its a hassle every time i move it so now i just strap the rear of the frame and push it instead of carrying it. its more of a convenience thing. plus i don't have the 2 grand right now to get my drop member! ha ha