Re: '57 Ford Custom 300 Tudor Sedan
I spy a machine tool you could eat off of in that last chassis shot. Motor specs?
|
Re: '57 Ford Custom 300 Tudor Sedan
4 Attachment(s)
Quote:
Quote:
The photos below are from the mid to late '90's. I was traveling a lot with work and other projects were taking my spare time which meant the Ford continued to sit neglected. And the more I looked at it, the unhappier I was. I never liked the way the steering sector interfered with the exhaust port at the rear of the driver side. It had forced us to run a header tube outside the frame which was an unfortunate compromise. Tried a Bronco sector, but it was unworkable. There was a power rack and pinion kit available, but the guy selling them had personal problems and had failed to deliver a number of sold kits, so I hung back and did nothing. Plus, the fuel cell and drum brakes were just so "yesterday". It would sit like this until early 2004. |
Re: '57 Ford Custom 300 Tudor Sedan
Quote:
|
Re: '57 Ford Custom 300 Tudor Sedan
Quote:
|
Re: '57 Ford Custom 300 Tudor Sedan
Looks like you are ALL IN, got to get Kathy a ride for the power tour.
|
Re: '57 Ford Custom 300 Tudor Sedan
5 Attachment(s)
Quote:
By the first of 2004, the project Chevy was gone and I'd acquired a rotisserie for the bodywork. I upgraded the plan a bit and stripped the chassis down to the bare frame and repainted it after removing the fuel cell and etc. Came by a partially completed stainless fuel tank and finished it out to mount under the trunk floor. I added a stiffening rib to the rear housing and had all the suspension parts blasted clean (third time) and powder coated with Anthracite and gloss clear. I had two 9" Ford rear disc setups, one from a Town Car and the other from a Versailles. The rear setup was easy peasy, but the front took a bit more engineering. I'd heard you could swap in Granada spindles and their front disc setup, but wasn't sure if the wheel location and steering would stay the same. "The Google" was still in it's infancy, so rather than buy more junk for a science project, I decided to make the junk I had work. Machined my own o-ring plugs to eliminate the e-brake mechanism and engineered the brackets to bolt onto the '57 stock spindle. Voila! Four wheel disc brakes. |
Re: '57 Ford Custom 300 Tudor Sedan
Outstanding! The suspense is killing me Vic. We're still only to '04? This is going to be killer but are you sure it's closer than Rusty?
|
Re: '57 Ford Custom 300 Tudor Sedan
5 Attachment(s)
Quote:
After fitting up the disc brakes on all four corners, I plumbed them with -3 AN hardware. Added an adjustable proportioning valve and a line lock for the ever important burnout ritual. The engine was ready to drop back in once the lines were run. I was still sitting on the fence about the headers. They presented a problem for the inner fenders as well as aesthetics. But the fix was elusive without removing the stock steering box and going to R&P. So they went back on for the time being. |
Re: '57 Ford Custom 300 Tudor Sedan
5 Attachment(s)
With the engine, transmission and rolling stock back in place the chassis was once again down on all fours. Replaced the Centerline wheel cap logos with Henry's logo. The existing collector setup was overkill, plus it interfered with my plans to run an X-pipe. So I shortened them up, added my X and a pair of DynoMax turbos. I eventually would have to truncate the roll bar crossmember to get the rest of the exhaust out the back, but I reinforced the stubs just in case I ever wanted to add the roll bar later. Yeah, right.
|
Re: '57 Ford Custom 300 Tudor Sedan
5 Attachment(s)
In late 2004, I pushed the chassis out of the way and mounted the body shell on the rotisserie. One of the key body elements I wanted was smoothness. So the first thing on the agenda was to shave the drip rails. Not sure if you've ever done it, but it's much more difficult than you would think. In an effort to keep the heat from warping the roof panel, I'd do a small section at a time. The main problem was dealing with the sealant used by the factory. After they pinch welded the roof on, they shot a thick, black, tar-like sealer into the seam. Heat would liquefy the material and cause it to run, thereby contaminating the weld. So I had to first carefully pry open the gap with a thin blade putty knife and scrape out the sealant. Progress was slow, but the results were what I'd envisioned. Now when people see it, they'll ask if the top is chopped because the look is subtly different.
While working on this area, I also rounded the upper forward and lower rear corners of the door openings . |
Re: '57 Ford Custom 300 Tudor Sedan
In for more.
|
Re: '57 Ford Custom 300 Tudor Sedan
Cool project, I will be following!
|
Re: '57 Ford Custom 300 Tudor Sedan
I love the radiused corners and the shaved drip rail!
|
Re: '57 Ford Custom 300 Tudor Sedan
5 Attachment(s)
Quote:
Quote:
Quote:
By November, 2005 there was so much surface rust on the floor, tubs, patched areas and etc. I decided to have the body dipped. I've had a couple done that way and never regretted it, although rust is usually the deciding factor. Some folks swear the caustic solution stays in the pinch welds and will ruin a paint job. Never had that happen, but the place I used in Houston lets the metal sit in a neutralizing solution after rust removal and then power washes it and wipes it down good with a product like GEM Rust Killer. Once it was back home, the next step was smoothing out the firewall, etc. The body had been on the chassis since returning from the metal stripper, but I needed better access, so I loaded it back on the spinner. These Fords had a nasty pinch weld that ran the length of the f/w as well as several openings that didn't fit in my plan. Welded in patches and started slinging bondo. |
Re: '57 Ford Custom 300 Tudor Sedan
4 Attachment(s)
More firewall, plus a few shots of the dash. I removed the speaker grille and patched and smoothed it out. Not evident in the photos, but I also filled the ash tray opening and windowed the dash for a DIN 1 radio and A/C vents. The defroster manifold had to be surgically altered to fit the Vintage Air setup.
|
Re: '57 Ford Custom 300 Tudor Sedan
What color are you looking at for the 57?....
|
Re: '57 Ford Custom 300 Tudor Sedan
Quote:
|
Re: '57 Ford Custom 300 Tudor Sedan
With a quick search I found a few images of two-tone 57's. I'm just not sure what your trim looks like. You may have seen these already, but just in case...
Brochure or ad for the 300 http://www.oldcarbrochures.com/stati...rochure-02.jpg http://www.regresspress.com/catalog-..._300_id920.jpg And a feature car on another website (says it's a fairlane 500 though.) http://www.cruisenewsonline.com/1957...00Feature.html |
Re: '57 Ford Custom 300 Tudor Sedan
3 Attachment(s)
Quote:
|
Re: '57 Ford Custom 300 Tudor Sedan
Hate to hear the news on the pickup but I am glad to see the thread on the 57. I enjoy watching how you approach and solve problems. Good instruction.
Dwight |
Re: '57 Ford Custom 300 Tudor Sedan
OK Vic ... I'm game. The 300 '57 is on my list of one of the best looking cars EVER.
I've always had an affection for post cars ... having had 3 chevy 2 sedans & 2 Fairlane sedans. I am also on a trek to complete my '64 fairlane right now. It's a bit more race carish with a complete tube frame, struct front & 4 link rear but plans are for street duty. I'll follow along. R 46 |
Re: '57 Ford Custom 300 Tudor Sedan
Found the link and subscribed! Thats one sweet project!
|
Re: '57 Ford Custom 300 Tudor Sedan
5 Attachment(s)
Quote:
Quote:
Quote:
The firewall was fairly complete, so I moved around the corners and cleaned up the cowl areas below the A-pillars. To make room for the Vintage Air suitcase, I had to remove the rain gutter area of the cowl. This left a large area open adjacent to the windshield wipers. I welded in patches to close it up as well as the rain channel ports on both sides of the cowl. No water allowed inside. After the bodywork was done on the entire cowl / firewall I applied sound deadener to the underside of the roof. This helped quite a bit while doing bodywork on the roof. By now it is mid 2006 and I was about ready to drop the body back on again to finish the trunk area and exhaust hangers. |
Re: '57 Ford Custom 300 Tudor Sedan
I'll bet nobody chem dips in Washington do they... Wish i had the option to concider..
|
Re: '57 Ford Custom 300 Tudor Sedan
Quote:
On a similar note, a few years ago in MO they passed a law that requires salvage yards to have a title for all cars they're parting out. Apparently there's no grandfather clause. A lot of yards with old classic cars couldn't meet the requirement, so they're crushing the cars and selling them for scrap. My custom bumper setup on the Ford wasn't developing the way I'd hoped, but I had a plan B that involved acquiring a front valance off a '59 Plymouth. Put out feelers and have had no luck. I wasn't aware of the issue until just recently. Guess it's the law of unintended consequences. |
All times are GMT -4. The time now is 10:49 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com