Re: 13" and 14" Corvette Brakes for C10's
Do you have something for the rear in 6 lug?
|
Re: 13" and 14" Corvette Brakes for C10's
PM sent...
Posted via Mobile Device |
Re: 13" and 14" Corvette Brakes for C10's
Is there any partcular Mcguaghys spindle that you need to work with this setup or is are they all compatable with the brackets?? Does the rotor thickness matter?
|
Re: 13" and 14" Corvette Brakes for C10's
Quote:
|
Re: 13" and 14" Corvette Brakes for C10's
do you have any of the 13" assembled kits and are they still 999?what would shipping be to 50428?thanks
|
Re: 13" and 14" Corvette Brakes for C10's
Quote:
|
Re: 13" and 14" Corvette Brakes for C10's
Question... I already have the McGaughy 13" Big Brake kits front and rear...Can the already cut spindle I have be adapted to work rather than buying another set of spindles. Mine are already on the truck, but I'd love a better looking caliper ;)
|
Re: 13" and 14" Corvette Brakes for C10's
Quote:
|
Re: 13" and 14" Corvette Brakes for C10's
Quote:
|
Re: 13" and 14" Corvette Brakes for C10's
Quote:
|
Re: 13" and 14" Corvette Brakes for C10's
I have a set of ECE 2 1/2" dropped spindles. What options do you have available to go with it? TIA.
R/ |
Re: 13" and 14" Corvette Brakes for C10's
Quote:
|
Re: 13" and 14" Corvette Brakes for C10's
2 Attachment(s)
Quote:
|
Re: 13" and 14" Corvette Brakes for C10's
Quote:
|
Re: 13" and 14" Corvette Brakes for C10's
I sent you a PM about your brake kit.
|
Re: 13" and 14" Corvette Brakes for C10's
Quote:
|
Re: 13" and 14" Corvette Brakes for C10's
Quote:
Thats cool! I have the calipers and rotors. When you get a chance shot me a cost on your spindles, hubs and brackets. |
Re: 13" and 14" Corvette Brakes for C10's
To the guys who want to source their own c5 or c6 parts. I supply the drop spindle, 4.75" bolt pattern hubs with bearings, seal, dust caps, and screw in 7/16" wheel studs, along with a bolt on mounting bracket for $600+shipping. You will need the rotors and loaded calipers to finish off the kit. I've seen take off vette parts as cheap as $100 on craigslist and swap meets
|
Re: 13" and 14" Corvette Brakes for C10's
Will the hubs work on the 04 trucks . If not do you have a 5lug kit for the 99-04 truck
Posted via Mobile Device |
Re: 13" and 14" Corvette Brakes for C10's
Quote:
|
Re: 13" and 14" Corvette Brakes for C10's
How much?
Posted via Mobile Device |
Re: 13" and 14" Corvette Brakes for C10's
$65 each
|
Re: 13" and 14" Corvette Brakes for C10's
Where are you located at? I am looking to buy a new set of hubs from eBay right now and rotors from r1 concepts
Posted via Mobile Device |
Re: 13" and 14" Corvette Brakes for C10's
Quote:
|
Re: 13" and 14" Corvette Brakes for C10's
OK, so if I'm starting from scratch and want 4 corner 13" brakes with single piston sliding caliper brakes with parking brake and the goal of easy service on the brakes, what can you do? I'd prefer to use something like SPP diamond slotted rotors with Hawk HPS pads. I think I'll get better pad area out of single piston sliders than some multi piston caliper, and I don't like drilled rotors, they tend to crack when you run them hard and eventually they look crappy anyway. I'm OK with going to 5 on 4 3/4" and changing out the rear axles to do that if it makes it easier to do off the shelf replacement parts in the future.
I'm planning out a project right now and want to do this all at once, I'm probably going to be using a Porterbuilt dropmember front with coilovers. Looking to do probably a 3" drop front and 4" or 5" in the rear.. I'm not just looking for brakes that look good behind wheels, I plan on using them and using them hard. Oh, project is a 69-72 Blazer/Jimmy and 18" wheels BTW, also want to stuff 295/45/18s on all 4 corners so I'm probably going to have to play around with backspacing to get everything to clear. Since these trucks lack a locking column I also plan to relocate the parking brake to inside of a Tuffy center console using a Lokar hand parking brake though I don't think that matters much. Way2lo2 sounds like you could supply such a requirement, no? |
All times are GMT -4. The time now is 04:10 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com