Re: which one would you build?
Man your a parts ordering pro!! :lol:
|
Re: which one would you build?
no doubt wished I had the cash to order all that stuff.
|
Re: which one would you build?
gonna get some work done on the truck today, will post pics of progress soon
|
Re: which one would you build?
well been working as much as possible on the truck, got alot done this week
got my wiring started, all 1/0 grounnds and power leads[IMG] http://img813.imageshack.us/img813/7897/pa090317.jpg[/IMG] By grasshoper at 2010-10-10 http://img38.imageshack.us/img38/313/pa080315.jpg By grasshoper at 2010-10-10 300 amp fuses, laying the ground work for the stereo system http://img2.imageshack.us/img2/3921/pa200407.jpg By grasshoper at 2010-10-21 fuses mounted, on some scrap aluminum , put some detailinng into these with a wire brush trying to achieve a scalloped look also wired up the controller for the twin e-fans, and mounted the radiator and fans permmanently! no more mock up http://img2.imageshack.us/img2/3921/pa200407.jpg By grasshoper at 2010-10-21 all the stainless braid hoses are going in, magna clamps on the ends, looks real clean http://img222.imageshack.us/img222/233/pa130361.jpg By grasshoper at 2010-10-19 drive shaft went in after being shortened by 2 inches, balanced and new carrier bearing, and all new heavy duty u joints http://img254.imageshack.us/img254/7736/pa130365.jpg By grasshoper at 2010-10-19 http://img508.imageshack.us/img508/8816/pa130366.jpg By grasshoper at 2010-10-19 some more pics of the install, I know im all over the place on this but theres so much to show, http://img145.imageshack.us/img145/5139/pa130373.jpg By grasshoper at 2010-10-19 had to massage the header with a bfh to gain clearance for steering shafthttp://img710.imageshack.us/img710/9/pa100345.jpg By grasshoper at 2010-10-10 http://img139.imageshack.us/img139/2743/pa090342.jpg By grasshoper at 2010-10-19 so to sum it up the motor and tranny are in and all the plumbing is on , gonna work on the wiring harness, and then replace the stock gauge cluster with a set of autometer gauges , lots more work to do but lots of progress made stay tuned for more pics and maybe a little video. give me some input, dont just look give me some feadback!! good , bad , or even ugly!!! |
Re: which one would you build?
1 Attachment(s)
it looking good man i found this gauge set up on fsc but it looks pretty sweet i kno its not the same dash but it looks sweet and itll give u somewhat of an idea
|
Re: which one would you build?
Quote:
|
Re: which one would you build?
been sick last few days wicked fllu going thru my area maybe I will get the harness back in the next few days,
|
Re: which one would you build?
Hope you feel better soon. The truck's coming together great. I like the fuse mounts. Any plans for new wheels?
|
Re: which one would you build?
Quote:
|
Re: which one would you build?
is that mashed in header going to affect anything? Do you got enough clearance now? Oh and im totally stealing that gauge cluster idea.
|
Re: which one would you build?
Quote:
|
Re: which one would you build?
Quote:
Dayum, you hit the lotto or what??...Nice Stuff!!! |
Re: which one would you build?
Start looking for a 2WD 14-bolt semi-floater rearend, the stock POS won't make it past the first 1-2 shift. The 14-bolt can handle it, though. You can use 12-bolt backing plates and drums, but you'll have to have the axles redrilled if you want to stick with 5-lugs.
Most builders will tell you that your headers are too big, those are about right for a hot 496. I wouldn't worry, though, it'll only cost you a bit of hp and tq, but it'll sure sound good! |
Re: which one would you build?
yeah these headers give me room to upgrade the motor down the road with a stroker set up, should work fine for now, plus they were the only full leghth header that would fit a bb in this year 1996 without serious welding and re-routing, they look good will flow well and Im not trying to break into the 10's with this truck just a cruiser with a little something extra under foot when needed, should be fast enough for around town and strong enough for occasional abuse, building more for show and something a little different than your run of the mill small block pick-up,
|
Re: which one would you build?
Yeah i think you struck your goal there :metal: ;)
|
Re: which one would you build?
Almost ready , should start it in a few weeks, been working alot so havent had the time needed to finish the wiring harness,
|
Re: which one would you build?
Cant wait to hear that beast run. Great job so far. :chevy:
|
Re: which one would you build?
should finish wiring harness this week , then gonna blow the dash apart and install the new gauges, pics coming soon stay tuned
|
Re: which one would you build?
well a little progress update, under the hood is just about done
http://img521.imageshack.us/img521/6581/pa230449.jpg By null at 2010-10-27 now gonna work on the dash, try and get some gauges mounted this week http://img99.imageshack.us/img99/5783/img3822e.jpg By null at 2010-11-05 check engine light I dont need no stinkin check engine light http://img526.imageshack.us/img526/9474/img3824v.jpg By null at 2010-11-06 stay tuned , more progress updates in a few days! |
Re: which one would you build?
wow the replys are flying in on this build , maybe i will generate some interest when I redo the interior?
|
Re: which one would you build?
dude, i love that motor! this is a bad ass build man, keep going!
|
Re: which one would you build?
I think the jealousy is setting in... LOL.
I wish there was a way for this project to happen to my truck! Looks great man! Can't wait to see more pics! |
Re: which one would you build?
wow thats nice and clean!
|
Re: which one would you build?
thanks for the support, should be firing up for the first time soon, gonna try and get a video, will post more pics and updates
|
Re: which one would you build?
sweet build.Can't wait to see it all together.I was just up in your area last weekend.
|
All times are GMT -4. The time now is 06:53 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com