Re: Cabs Need any cuts, parts etc?!
 

Paypal sent thanks

Re: Cabs Need any cuts, parts etc?!
 

I could use the deluxe trim beneath the rear window with the clips, etc.

Also, I need an A/C evaporator box. Specifically the inner metal trim piece but I will buy the entire box if separating is an issue.

Thanks,

Wil

Re: Cabs Need any cuts, parts etc?!
 

One small ding in the trim, all clips and gas cap. $30 shipped

Adam


http://i163.photobucket.com/albums/t...ps7f731e35.jpg

http://i163.photobucket.com/albums/t...ps87ca71d6.jpg

http://i163.photobucket.com/albums/t...pse5017a49.jpg

http://i163.photobucket.com/albums/t...psccab7d97.jpg

Re: Cabs Need any cuts, parts etc?!
 

Look good, I can help you with that!

Adam

Re: Cabs Need any cuts, parts etc?!
 

I will take the gas cap, cab trim, 12 clips (AND THE TWELVE SCREWS) shipped to me at 79106 for $30, Pm me with payment instructions, thanks a bunch.

Re: Cabs Need any cuts, parts etc?!
 

This is an original two tone truck, it has factory "studs" to put the clips on. Search the forum for other methods of adding the paint divider trim..looks pretty simple and quite a few have done it.
I accept PayPal "personal" at: playersnmv@aol.com

Adam

Re: Cabs Need any cuts, parts etc?!
 

Got another set of cab trim? And, how about the A/C evap box?

Re: Cabs Need any cuts, parts etc?!
 

I have a perfect 72 RV cab that the back was cutout for a pass thru. It was cut above and below the back window opening. I want to get in line for these areas and will send you the dimensions in the morning so you can quote the patches.

Thanks,

Re: Cabs Need any cuts, parts etc?!
 

Hey Budnikguy,
I need approx. 46" wide x 6" tall x 6" deep (should put us into the headliner area) on the upper.

Also need 46" wide x 30" tall x 3" deep (floor) on the lower.

Might also be interested in cowl patches for another cab I have. Same areas that *Gregg* was describing "I need part of the right side cowl/firewall right above the heater box & on the left side too to the right of the wiring block." not as big a deal please quote separately with and without. Let me know if you need more specific info for these.

Shipping to 84010 or Greyhound to Salt Lake terminal would also work.

Thanks,

Re: Cabs Need any cuts, parts etc?!
 

I need the driver side rocker and cab corner and into the floor where the outer supports weld to the inner support(all in one piece would be optimal)

Re: Cabs Need any cuts, parts etc?!
 

Interested in pieces from both sides, including cab corners, inner/outer rockers, where kick meets floor pan, lower fender extension, etc. Basicly the bottom of cab from just above body line not including center of floor. If that doesnt makesense PM me your # and I will call you and explain. Need both sides. Shipped to 27587?

Re: Cabs Need any cuts, parts etc?!
 

Adam, how much for the floor sheetmetal. I cropped the section I need.

Re: Cabs Need any cuts, parts etc?!
 

In need of a passenger side cab corner no rust plese lmk shipped to 78259 TX...

Eric (Evaded)

Re: Cabs Need any cuts, parts etc?!
 

Adam, are you still parting the cabs out.

Re: Cabs Need any cuts, parts etc?!
 

Looking for roof section. Im in OC and can pick up if possible.

Re: Cabs Need any cuts, parts etc?!
 

I believe I do have an extra set of trim...tomorrow is my day off. I will double check and get pics of the trim...and I can definitely help you with the a/c evap box.

Re: Cabs Need any cuts, parts etc?!
 

$35 shipped, please confirm with measurements of how high you need the cut...assuming the full width between cab corners and 3-4" high/up?!

Re: Cabs Need any cuts, parts etc?!
 

$45.00 shipped for both sides, please confirm with measurements exact size.

Adam

Re: Cabs Need any cuts, parts etc?!
 

On the RV patch pieces, I would need $60 plus Greyhound cost...depending on box size, probably 30-40 to ship. For the firewall pieces, both sides for $45 shipped depending on exact measurements. Could also ship those pieces with the other RV patches and save you some $...lmk.

Adam

Re: Cabs Need any cuts, parts etc?!
 

You want to come up? or are we talking about shipping it? $50 if you come up...figure another 25 to ship, so $75 delivered. LMK

Adam

Re: Cabs Need any cuts, parts etc?!
 

Shipping those big chunks may be a killer...you might look into what a freight cost would be...by zip is 92508.

Re: Cabs Need any cuts, parts etc?!
 

Please get me exact measurements, figure around 35 shipped.....lmk

Adam

Re: Cabs Need any cuts, parts etc?!
 

let me see how this works out with others ahead of you needing similar areas, and I will let you know there on...Thanks

Adam

Re: Cabs Need any cuts, parts etc?!
 

$20 come and get it...Just get me exact measurements...lmk

Adam

Re: Cabs Need any cuts, parts etc?!
 

yes sir, and just responded to your request...ty