Re: "Project Orangepeel" 52 A.D
Quote:
|
Re: "Project Orangepeel" 52 A.D
I love the build. Please keep it up.
|
Re: "Project Orangepeel" 52 A.D
Quote:
A.K.A. welder grinder etc. go to the scrap yard and pick up a piece of 4" tube 1/8" wall and cut if half to make the C Mark... |
Re: "Project Orangepeel" 52 A.D
Quote:
were not very good looking hence the reason i cut my own.. Mark... |
Re: "Project Orangepeel" 52 A.D
Mechanixman Thanks i'll keep the pics coming!
Mark... |
Re: "Project Orangepeel" 52 A.D
1 Attachment(s)
Ok on to the cab!!
first shot of the firewall as it rolled in WAY to many holes for me so time to fill!!! |
Re: "Project Orangepeel" 52 A.D
1 Attachment(s)
The next shot was after alot of welding,grinding etc. the remaining holes were left till I made up my mind of what to do with floor.
|
Re: "Project Orangepeel" 52 A.D
1 Attachment(s)
This is of the inner kick pan rot and part of the floor.
|
Re: "Project Orangepeel" 52 A.D
2 Attachment(s)
these next 2 are of floor pan and the outer drivers side kick pan..
|
Re: "Project Orangepeel" 52 A.D
2 Attachment(s)
The pics here are of the damaged pieces removed and now replaced..
|
Re: "Project Orangepeel" 52 A.D
2 Attachment(s)
These are the inner and outer lip for the fender to bolt to.
As well as the smaller panel replaced |
Re: "Project Orangepeel" 52 A.D
2 Attachment(s)
these two are of the toe board as I made the panel and it was installed.
|
Re: "Project Orangepeel" 52 A.D
Nice patch making. I enjoy it.
|
Re: "Project Orangepeel" 52 A.D
2 Attachment(s)
These pics are of the inner toe board and kick panel replaced.
As well as the passenger side being cut out. |
Re: "Project Orangepeel" 52 A.D
3 Attachment(s)
Here is some shots of the inner cab section. I used Eastwood rust encapulator then maid my new patch. Using a hole punch I popped holes around the piece so I could spotweld it in place.
|
Re: "Project Orangepeel" 52 A.D
Nice work Reaper...be good for another 60 years!
|
Re: "Project Orangepeel" 52 A.D
Quote:
|
Re: "Project Orangepeel" 52 A.D
3 Attachment(s)
These are of the floor pan removed,patch panels and the lower A pillar replaced
|
Re: "Project Orangepeel" 52 A.D
3 Attachment(s)
These few are of the floor being replaced. a pic of the body mount I made, I used 2x3 tube and welded in. The last pic is of the cab patch, I cut this out do to a large crease down the center of the stock piece (damaged during tow bringing her home)
Mark... |
Re: "Project Orangepeel" 52 A.D
1 Attachment(s)
First pic is of the cleaned up area for the new patch.
|
Re: "Project Orangepeel" 52 A.D
2 Attachment(s)
these two are of fitting the panel and getting it tacked in.
i did not show it but i made a panel that was welded in from the backside to block off the vent. |
Re: "Project Orangepeel" 52 A.D
1 Attachment(s)
these next few shots were of welding all done and the metal finish done. the last pic (real fuzzy sorry!) shows the block off plate over the vents. and the inner panel that needs to be replaced.
|
Re: "Project Orangepeel" 52 A.D
1 Attachment(s)
#2 pic.
|
Re: "Project Orangepeel" 52 A.D
1 Attachment(s)
#3 pic
|
Re: "Project Orangepeel" 52 A.D
The butt weld came out really nice! Well done!
|
Re: "Project Orangepeel" 52 A.D
Thanks A.D.
|
Re: "Project Orangepeel" 52 A.D
1 Attachment(s)
This is of the new panel i made for the inner kick panel.
|
Re: "Project Orangepeel" 52 A.D
1 Attachment(s)
The panel all welded in.
|
Re: "Project Orangepeel" 52 A.D
1 Attachment(s)
This is the new toe board I made..
|
Re: "Project Orangepeel" 52 A.D
1 Attachment(s)
Toe board all welded in..
|
Re: "Project Orangepeel" 52 A.D
1 Attachment(s)
Quick shot of the repairs from the front..
|
Re: "Project Orangepeel" 52 A.D
1 Attachment(s)
This is the drivers side floor removed and shows the 2x4 tube witch is now my new cab mount. (has rubber under it)
|
Re: "Project Orangepeel" 52 A.D
1 Attachment(s)
Fitting the new piece viewing from passenger side.
|
Re: "Project Orangepeel" 52 A.D
2 Attachment(s)
Floor pan replaced and mounts all done
|
Re: "Project Orangepeel" 52 A.D
Looks great....keep it up.
|
Re: "Project Orangepeel" 52 A.D
Quote:
Mark.. |
Re: "Project Orangepeel" 52 A.D
Very nice welds, looks good.
|
Re: "Project Orangepeel" 52 A.D
Quote:
|
Re: "Project Orangepeel" 52 A.D
1 Attachment(s)
This post is of my bed mounting idea.
I will not be using the O.E. components for mounting the reason being i wanted to have a better way of mounting bed to frame and easy to remove. I will use a solid sheet for the wood and dress it with metal ribs. |
Re: "Project Orangepeel" 52 A.D
1 Attachment(s)
This is the tube structure I built. I used 1x1 tube and made a frame then made legs coming down to chassis. the feet of the legs are then bolted to the chassis. the bed is then bolted to the frame i built. so if you need to the entire bed can be unbolted and removed with out the frame or keep the bed bolted to the frame and the bed/frame can be unbolted from chassis and removed..
|
All times are GMT -4. The time now is 05:12 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com