Re: Parting 1971 Suburban (NM)
 

Unfortunately all of the headliner and all of the bows are gone. I'll see how many of the clips I can come up with. Do you need the upper trim to?

Re: Parting 1971 Suburban (NM)
 

sorry, will have to pass on gauges.

Re: Parting 1971 Suburban (NM)
 

No worries.

BTTT

Re: Parting 1971 Suburban (NM)
 

Rob,

Found some pictures of what I need. It is the area of the inner cab where the sun visor mounts and the left side where upper fender mounts (the captured nut area.) I also need the entire dash, unbolted and the pinch welds drilled out at the windshield area. Let me know.

Re: Parting 1971 Suburban (NM)
 

How 'bout I bring you this........:).
.

Re: Parting 1971 Suburban (NM)
 

That looks about right. The cab is actually visually rust free. I will have to see once I start stripping it. How is the dash, is it AC? If you start cutting the burb up, I think the 2 patch panels I need would end up being pretty small.

Re: Parting 1971 Suburban (NM)
 

Non ac dash. Radio has been cut for the new style radio. It will be easier for me to cut it across the rockers and roof. I can bring it when I come this fall.

Re: Parting 1971 Suburban (NM)
 

bump

Re: Parting 1971 Suburban (NM)
 

sent you a PM.

Re: Parting 1971 Suburban (NM)
 

bttt

Re: Parting 1971 Suburban (NM)
 

Yes Rob, thanks for asking. I could use the suicide knob on the steering wheel..........hehe I will wait to see whats left and clean up the scraps like I always do. Talk to you soon my friend, Mike

Re: Parting 1971 Suburban (NM)
 

Do you still have the rear hatch latches? I need the two that bolt to the side of the top for the rear hatch to latch to for my 72 Blazer. Thanks for your help.

Re: Parting 1971 Suburban (NM)
 

You saw that, huh?! That was the first thing I pulled off, :lol:. I'm not sure if I'm going to use it yet, if I don't I'll let you know. I'm getting ready to start chopping the Burb up in a couple of weeks, so send me your wish list, :D. Take care.

Are you talking about 1 or 2? Let me know.
..
..

Re: Parting 1971 Suburban (NM)
 

Looks like the Burbs rear hatch mechanism is different than the Blazers. I was thinking they were the same. It would look something more like #2, but I can not see it that well. Sorry, maybe I am confused on the interchangability. Sorry for the confusion.

Re: Parting 1971 Suburban (NM)
 

Here's a better picture:

.

Re: Parting 1971 Suburban (NM)
 

PM sent

Re: Parting 1971 Suburban (NM)
 

Thank you very much for the better picture. I can clearly see these are not the same as the Blazer. Thanks again for your time and help.

Re: Parting 1971 Suburban (NM)
 

Hi Im in need of a good set of rear door panels for 3rd door and ds rear non door. how are yours? shipping to 92025?

Re: Parting 1971 Suburban (NM)
 

PM returned.

No worries. I'm sure someone on the board has what you need.

Passenger side is good. Someone cut a 4" corner off of the drivers side, :(. The part that is cut off is behind the seat and hard to see. Let me know.

Re: Parting 1971 Suburban (NM)
 

ttt

Re: Parting 1971 Suburban (NM)
 

Just a friendly bump for ya Rob.......

Re: Parting 1971 Suburban (NM)
 

Do you still have the rear wheel well inner tubs?

JJ

Re: Parting 1971 Suburban (NM)
 

Yes, what all do you need?

R/

Re: Parting 1971 Suburban (NM)
 

Would like to get the inner wheel well that bolts to the floor. It can be cut from the outer at the factory seam. I want to use them to mini-tub my 57 short bed.
Thanks,
Johnny

Re: Parting 1971 Suburban (NM)
 

PM sent.