Re: Project 30 years sitting
2 Attachment(s)
...
|
Re: Project 30 years sitting
2 Attachment(s)
95% of my exhaust. Trying to decide how to do the exits.
|
Re: Project 30 years sitting
1 Attachment(s)
new rubber came in 7 days early :metal:
|
Re: Project 30 years sitting
Got the tires on it, looks like a 4x4 now.
Went to run it off the new tank/electric pump tonight. Blew out the carb gaskets. The inline regulator was suppose to be pre-set at 7psi, but somehow got up to 10-12'ish and sprayed fuel everywhere. |
Re: Project 30 years sitting
Full exhaust done
2nd fuel regulator on, and its not the right one, but it runs on a correct fuel tank vent lines routed and breathers mounted for axles waisted 3hrs in the middle of the day for work, ugh |
Re: Project 30 years sitting
2 Attachment(s)
In this first image. Can someone tell me the name of this part?
2nd image is all thats left of my exhaust build. I would say I designed it fairly well. |
Re: Project 30 years sitting
2 Attachment(s)
new tires on...
|
Re: Project 30 years sitting
Is that the top of the door window frame? If it is there is a plastic piece that goes there to close off the cut end of the window frame.
|
Re: Project 30 years sitting
Thats where the "a"post joins with the removable top. I have the plastic thing on both doors. But this metal thing, I only have it on the pass side.
|
Re: Project 30 years sitting
I think that was part of the original seal set for the top where it meets the door glass. I think the new ones are made differently and if needed, the metal part should come with the new seals.
|
Re: Project 30 years sitting
huh, ok. New seals are on my next lmc order.
|
Re: Project 30 years sitting
original goal met after a few setbacks.
http://www.youtube.com/watch?v=sJCg6...ature=youtu.be Needs ball joints bad as its all over the road. Needs carb tuned and I have no clue how to do that. |
Re: Project 30 years sitting
says videos private :(
|
Re: Project 30 years sitting
fixed, sorry
|
Re: Project 30 years sitting
Congratulations! Getting it to move under its own power is always a plus. Sounds pretty good, if a bit doggie. Didn't sound like much with carb issues though. Might just need more advance on the timing. I like how the exhaust sounds.
|
Re: Project 30 years sitting
1 Attachment(s)
Still working on it running right issues. We can get it to idle and rev great in park. But you put it in gear and put a load on it, and it just bogs down n stalls.
But I did drive it around the neighborhood in the snow/ice since you dont need to go fast anyway. Lots of looks, smiles, and waves :lol: Ordered the bolts and spacers for a body lift. Wow that was expensive :cuss: Still need to order the new mounts. |
Re: Project 30 years sitting
Sounds like a vacuum leak. Check the hoses and connections, also the brake booster and around carb and manifold. You guys have more snow than we do, but I bet its warmer.
|
Re: Project 30 years sitting
When we first started it, we slowly connected things checking vac. As we have added, nothing changed.
|
Re: Project 30 years sitting
Got a vac gauge? It changes with timing also, or if a valve is out of adjustment. Same symptoms I had with my jimmy. I had to adjust the valves to get the vacuum back.
|
Re: Project 30 years sitting
Yea, we have had a gauge on it while adding all the stuff. I installed an incab one so I can monitor while driving.
|
Re: Project 30 years sitting
Sounds like you have that covered then. Good luck with the rest of the tuning. I've got a carb rebuild kit sitting on my air filter right now so when the day comes I can actually take it for a drive I'll have it ready.
|
Re: Project 30 years sitting
junkyard score!!
dash speaker grate dash speaker speaker bracket headlight switch dual horn setup... only got one horn as I have one already and didnt have tool to grab the second. tow hooks that can easily be modded and installed. |
Re: Project 30 years sitting
Adjusted timing up to 20deg. Runs 1000x better. Now to fix this brake light thats stuck on in the dash. Bad prop valve?
|
Re: Project 30 years sitting
Quote:
|
Re: Project 30 years sitting
:clap:
|
All times are GMT -4. The time now is 06:14 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com