Re: 1953 chevy 1100 gigis truck
 

I am sorry to hear of his passing, man. Hopefully you can build this in his honor or something like that.

I understand what you are saying, sometimes if I do something "just for now" it may remain that way. I hope you are having some fun on this and it can remind you of good times. I can't believe how well that yellow paint came up - hopefully you can keep it.

Re: 1953 chevy 1100 gigis truck
 

The tire I have now are 275/55r22 on the front, converting overall diameter and width comes out to be 31.4 inches tall and 10.46 wide or something like that.
Since the tires just rub now, I fiqured if I went could go to a narrower tire and do some other mods I would gain a comfortable clearance to the fenders so I know I for sure won’t be any bigger of a tire. Since being 22 in rims options are limited especially if I don’t want to spend $1000 a tire. What I’ll ate it’ll end up with is a 29 inch tall and 9 inches wide hopefully won’t look to small in the big opening and also have the benefit of being closer to the ground

I like threads with lots of pics so trying to do the same! :wop:

Re: 1953 chevy 1100 gigis truck
 

Yeah it cleaned up nice, I have some rust to deal with that’s into the yellow but I think I can hide it. I’ve been thinking of trying the “poppies patina “ or might end up just clearing the hole thing

Re: 1953 chevy 1100 gigis truck
 

have you seen this site for tire sizes and comparing a cojuple tires next to each other? there are tabs to check out other stuff.
https://tiresize.com/comparison/

Re: 1953 chevy 1100 gigis truck
 

another handy visual tool if you plan to swap offsets. also has spots to put your fender clearances etc
https://www.wheel-size.com/calc/

Re: 1953 chevy 1100 gigis truck
 

Yes I have used the tire size calculator, the second one is net. I don’t plan to swap off set off.

Re: 1953 chevy 1100 gigis truck
 

curious, what are the wheels from, a donor or aftermarket?

Re: 1953 chevy 1100 gigis truck
 

GM transport rims, there 22x9

Re: 1953 chevy 1100 gigis truck
 

oh, ok. i've seen those before at the dealer but never connected the dots. the dealers scrap those wheels but that may be a GM policy or something. I heard they are not road legal, is that a thing or just something the GM parts guys tell you so they can sell more spendy wheels?

Re: 1953 chevy 1100 gigis truck
 

The dealers are so pose to scrap them as there is no dot number on them. Have seems lots of truck run them, gm most likely didn’t want to pay extra to get them certified if they were just going to be scrap

Re: 1953 chevy 1100 gigis truck
 

Ran into a fitment issue when test fitting the hood. Flipped the hood over and didn’t realize there is a hood brace that is now interfering with the firewall.
Too late to move the firewall so I moved the brace out and it seemed to add some rigidity to the hood.
Also got the motor and trans pulled out of the frame, hope to take the frame into work and give it a wash before I start to shorten the wheel base

Re: 1953 chevy 1100 gigis truck
 

Been awhile since I was under the hood of an AD. is that where the hinges bolt up? You could always do a front flip hood.

Re: 1953 chevy 1100 gigis truck
 

The hinges bolt to the mount the springs bolted to the brace that I moved but I was looking at doing something other than the springs

Re: 1953 chevy 1100 gigis truck
 

I kept my hinges, but removed the springs and installed prop rods.

The hood sits very flat on the cowl now, without the springs.

Just a suggestion

Re: 1953 chevy 1100 gigis truck
 

Yeah I was also thinking of that, I think I’ve looked through your thread your truck looks very familiar. I also found Lsfab.com they make some mounts to convert it to gas shocks

Re: 1953 chevy 1100 gigis truck
 

110% jealous of the firewall stretch, something i thought a lot about earlier on. that extra foot well would be MONEY

Re: 1953 chevy 1100 gigis truck
 

Had a productive couple of days! Set up and got the frame shortened, I needed to get the drive shaft mocked up so I can figure out the trans tunnel. Got some firewall done before I put the cab back on the frame :metal:

There was a pile of dirt in the frame

Re: 1953 chevy 1100 gigis truck
 

Got some good progress on the floor done the last couple days :metal:
Hoping to get the sheet metal done by the end of January so I can get the interior and firewall painted

Re: 1953 chevy 1100 gigis truck
 

Been a while since ann update, have been working a couple hours here and there. Got both kick plates done, got my pedals and steering column mocked up. Front end/rad support partial mounted.
Swapped out the front lower control arms swapped out for 2wd ones, will get some better pictures of of what i did to the front end.

Re: 1953 chevy 1100 gigis truck
 

:metal: