Re: DBW pedal mounting bracket
 

PM me your address and I'll talk to the post office.

Re: DBW pedal mounting bracket
 

Thanks for the purchase! Only 10 Left!

Re: DBW pedal mounting bracket
 

Got it yesterday. It looks great. Thanks a bunch

Re: DBW pedal mounting bracket
 

Are these still available ? I would like to package one with the hood brackets if you do.

Thanks, Anthony

Re: DBW pedal mounting bracket
 

Yes I Do! Text me.

Re: DBW pedal mounting bracket
 

Need one for a 05 truck pedal if you have one available.

Re: DBW pedal mounting bracket
 

Yes sir! PM sent and here's a link to that thread: http://67-72chevytrucks.com/vboard/s...d.php?t=651123

Re: DBW pedal mounting bracket
 

Ok,Thanks

Re: DBW pedal mounting bracket
 

Intestred in a bracket for my 86. I have a pedal from an 05 Cadillac Escalade EXT.

Re: DBW pedal mounting bracket
 

I don't make a bracket specifically for the 73-87, but some guys have modified my 67-72 bracket to work on the 73-87. LMK

Re: DBW pedal mounting bracket
 

For all of the guys looking for a pedal bracket to work with the 73-87 trucks, here's a thread that has some great info in it:

http://67-72chevytrucks.com/vboard/s...d.php?t=692222
http://www.hotrodlane.cc/Streetstories/81%20swap.pdf

Apparently a factory OEM gas pedal from a 94-02 CHEVY GMC 6.5L V8 DIESEL (PN 15984422) will bolt right in. You have to repin a few wires, but it's supposed to be pretty straight forward.

The .pdf file has a complete discussion on the entire install, but here is a small snippet:

"This is the installed Pedal Position Sensor AKA Drive by Wire pedal.
I used one from a 1998 6.5 Diesel truck as it bolts right up and is a closer match
than the later Silverado pedal. A couple of the wires do have to be moved as it is
internally wired different. Basically, there are three different sensors in the pedal
and the PCM compares all three of these to determine how much throttle
opening the drivers is requiring. If these three sensors do not agree, a code will
be set and the PCM takes a best guess at what the throttle opening should be.
The gray wire was moved from location A to J, the Brown wire was moved from
location E to A and the Yellow wire was moved from location J to E. I also had to
add a slot in the connector plug so it would plug into the pedal."

PLEASE NOTE I HAVEN'T TRIED THIS ON A TRUCK, I'M JUST PASSING THE INFORMATION. DO YOUR HOMEWORK BEFORE YOU PURCHASE ANY PARTS!!!!

Good luck with your LS Swap!!!

Re: DBW pedal mounting bracket
 

Rob, i would like one of your corvette pedal brackets, i have sent a Paypal payment to the email listed on page 1
Paypal: robhartley@aol.com, enter "CPB" in message block.
Thank you!

Re: DBW pedal mounting bracket
 

It should ship today. Thanks!

Re: DBW pedal mounting bracket
 

Rob, I received my bracket today, excellent service, Thank You!:metal:

Re: DBW pedal mounting bracket
 

Rob, just sent a Paypal payment for a Gen IV pedal bracket for a 72. Thank you.

Re: DBW pedal mounting bracket
 

Glad you like it! Thanks again.

Your bracket shipped today via the USPS. Thanks!

Rob

Re: DBW pedal mounting bracket
 

bump

Re: DBW pedal mounting bracket
 

Just wanted to say that interestingly enough I too had the same problem as "derotoreut" with my holes not lining up and my blazer is a '72 purchased in Texas. It wasn't a problem for me, I just lined up the bottom hole, drilled 2 new holes and welded up the old ones. I wonder if it would be location, mine was made in April of 72 in Flint.

Re: DBW pedal mounting bracket
 

Hi Rob,
I need one of the Corvette pedal brackets,I'm going to send you the payment in a few minutes.
Thanks Brian

Re: DBW pedal mounting bracket
 

Got it Brian, thanks! It will be in the mail Tuesday. Let me know if you have any questions. Merry Christmas!

Re: DBW pedal mounting bracket
 

Good question. There seems to be no rhyme or reason to which ones are different.

Re: DBW pedal mounting bracket
 

Thanks Rob
Have a great new year !!

Brian

Re: DBW pedal mounting bracket
 

Hi Rob,

I am going to use a DBW truck pedal out of a 2008 Gen IV in my '71. Do you know if I need the bracket for the Corvette pedal or the bracket for the Gen III trucks? Here's a picture of my pedal for your reference.

Thanks Rob.

Re: DBW pedal mounting bracket
 

The Gen III bracket should work.

Re: DBW pedal mounting bracket
 

Thanks Rob. Will PayPal you this weekend.

Re: DBW pedal mounting bracket
 

:metal:

Re: DBW pedal mounting bracket
 

Too bad that this is happening. At least I'm not the only one. I wonder why? If you ever find out any more on this I would love to hear.

Re: DBW pedal mounting bracket
 

HartR, do you have anymor in stock? I would like to order one if you do. Thanks

Re: DBW pedal mounting bracket
 

Yes I do! Paypal is robhartley@aol.com. Thanks!

Re: DBW pedal mounting bracket
 

Good deal for just 50 usd

Re: DBW pedal mounting bracket
 

I've got an 86 k10 with a 2006 Silverado 5.3 pedal. Do you have a bracket for this setup? Do I need to upload a pic of anything? Minor modifications not an issue.

I'll share this info over at GMSquarebody if it works out.

Thanks Dude
'maro

Re: DBW pedal mounting bracket
 

Please post pictures!

Re: DBW pedal mounting bracket
 

Not sure if you need a pic of the full pedal.

Re: DBW pedal mounting bracket
 

The bottom pic tape measure has the 1" mark lined up with the center of the top hole if that helps.

Re: DBW pedal mounting bracket
 

I think you can probably make it work, but I can't guarantee it. Let me know what you want to do.

Re: DBW pedal mounting bracket
 

Do you have any of the Corvette pedal mounting brackets left?

Re: DBW pedal mounting bracket
 

Yes I do!

Re: DBW pedal mounting bracket
 

Just sent you paypal. The address attached is correct to send to.

Thanks!

Re: DBW pedal mounting bracket
 

Will ship it tomorrow. Thanks!

Re: DBW pedal mounting bracket
 

Pay pal sent