Re: 77 c10 5.3ls turbo
Did not dyno tune it, will do so after I get my to do list completed and put some miles on it. In the spring some time.
|
Re: 77 c10 5.3ls turbo
Nice lowered stocker look with a killer drivetrain. Well executed. Give a shout if you're going to bring it over to the west side ever. It'd be cool to see it in person.
|
Re: 77 c10 5.3ls turbo
3 Attachment(s)
Got the pcv setup completed not sure it will work but Ill give it a go. Welded a 10an bung on both the pass. and drivers valve cover. Connected bung with some braided lines to the oil catch can mounted where the battery tray was. I googled what other folks are doing for pcv systems and most are much more complicated. Most have a clean line and dirty line, check valves. I dont have either of my lines dedicated to clean or dirty. Seems like my setup would self equalize. I guess ill find out.
Picked up a set of factory c10 caps for cheap. Not sure I like them but they do help with the sleeper look. |
Re: 77 c10 5.3ls turbo
Thanks for the inspiration can’t wait to hear how it drives after the 10 lb spring
|
Re: 77 c10 5.3ls turbo
Actually just ignore the clean side/ dirty side stuff. I'd highly recommend getting some sort of PCV setup... not for emissions but you really need engine vacuum to "suck" out the oil mist! This is the exact routing I ran at 18psi making 725rwhp through a 2005 5.3:
https://ls1tech.com/forums/attachmen...psvinoxqvk.jpg |
Re: 77 c10 5.3ls turbo
Need to add some of those great pictures from Facebook buddy.
|
Re: 77 c10 5.3ls turbo
Hey JRPpntiac I am guessing you are past the shake down miles? How is this thing running and have you made any changes or upgrades at this point?
|
Re: 77 c10 5.3ls turbo
Haven't made any changes and haven't put as many miles on it as expected. But it is running very well, a pleasure to drive and it rips. Drove maybe 250 miles. Picked up some other cars this spring that diverted my attention. One of them being an 90 SS 454 .
At 13lbs and tuner says I will need a speed density to go even a 1/2lb more. Haven't had it on the dyno. Hope to do so in the next month or 2. Tuner is really busy and Im not in a hurry. Only thing I still need to trouble shoot is the VSS, it isnt working so it sometimes dies idle.. |
Re: 77 c10 5.3ls turbo
Quote:
|
Re: 77 c10 5.3ls turbo
Awesome build!
|
Re: 77 c10 5.3ls turbo (Dyno numbers)
1 Attachment(s)
Good news - Had the truck dyno’d. Running about 12.5 lbs
528hp/501tq Bad news - it was making some lifter noise before the Dyno. I think one lifter has let go. Will pull the heads and inspect. If lower end looks good probably will upgrade heads/arp head bolts and a couple other things. If it is a piston problem I’ll scrap the 5.3 and build a 6.0 and shoot for 700 hp. |
Re: 77 c10 5.3ls turbo
Awesome! That’s impressive, and 12 lbs is plenty of boost. Do you have head studs now? There are a few rocker kits that would suite you well if you just have stock rockers now and no upgrades. Fingers crossed it’s just a rocker issue and you can save some cash!
|
Quote:
Posted via Mobile Device |
Re: 77 c10 5.3ls turbo (Dyno numbers)
Sooo....by my math that's about 660HP at the flywheel!
Pretty dang good, I'd say! Quote:
|
Re: 77 c10 5.3ls turbo
Awesome numbers.
|
Re: 77 c10 5.3ls turbo
Quote:
Which adapters did you use for the motor mounts? Thanks!! |
Re: 77 c10 5.3ls turbo
Ground the clam shell. Don't remember the brand of the mounts but they were the standard flat plate 1/4 steel type. If I was to do it again I would use a solid motor mount. #1 I'm looking for more horsepower and probably should switch over. #2 they have a smaller profile.
|
Re: 77 c10 5.3ls turbo
1 Attachment(s)
I’ve been busy and it’s been cold so truck has been sitting for a few months. Got back into it today and turns out I had a broken spring land. Don’t know enough about broken piston lands to make any comment on why it broke. Not sure if I am going to go cheap and find a used piston, or spend some $. I had been looking at Craigslist all winter hoping a cheap 6.0 would pop up to start a higher HP build. It never did.
|
Re: 77 c10 5.3ls turbo
I would find a used piston and then increase your ring gap. Thats what cause the broken ringland.
|
Re: 77 c10 5.3ls turbo
Quote:
|
Re: 77 c10 5.3ls turbo
I did order a used piston/rod on ebay so I am going that route. I'll look into increasing the ring gap.
|
Re: 77 c10 5.3ls turbo
1 Attachment(s)
Nice and impressive install I hope to do to my truck some day!
|
Re: 77 c10 5.3ls turbo
Get the truck back together yet?
I am nearly done with my second LS turbo squarebody. Both 6.0. |
Re: 77 c10 5.3ls turbo
3 Attachment(s)
Truck is back together and running good, haven’t driven it much. Been busy with a hemi roadrunner project, Not an original hemi car.
|
Re: 77 c10 5.3ls turbo
I am new here and this is the first time I have looked at your build. I am impressed at the thought put into this and workmanship. A few years ago I built a 73 Camaro with a single 91mm T6 turbo and a BBC. It took 2 years to complete and I had a WHOLE new respect for pipe fitters and fab work. It taught me how important it was to think ahead when fabbing. I believe I did everything at least 3 times before moving on to the next thing. ha ha
Your build gives me the urge to do a turbo in the 56 but I'm not sure I have the patience to do another. Oh, I saw where you have a ring gland lift on a piston. If you know at what psi your were running win it let go, you may want to bump your waste gate down a couple psi. That normally happens when the ring gaps close and butt due to tight gaps using boost. |
Re: 77 c10 5.3ls turbo
I never did summarize what changes I made with the most recent tear down. 1 used eBay piston and rod, eBay head studs, ls9 head gaskets, arp cam bolts, new lifters. Nothing to add more performance, just some small things for reliability (hopefully).
|
Re: 77 c10 5.3ls turbo
Clean truck!
|
Re: 77 c10 5.3ls turbo
Love this thread. Gave me some ideas as to how to mount the inter cooler.
|
Re: 77 c10 5.3ls turbo
Love the build. and color.
|
All times are GMT -4. The time now is 05:30 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com