![]() |
Re: 56 Chev Garage build
5 Attachment(s)
A little update got a 327 large journal rebuilt from a friend of mine, it had power pack heads and right side blown head gasket, I found late camel hump heads and swapped them out with new gaskets and harmonic balancer. I also started to install bed wood, going to hide bed strip bolts that is why no holes in pictures stay tuned for that one. I also found another intake that was painted orange so I smoothed it out and it is going on 327 motor. The intake that is on it I am not happy with it from China and runners hit my valve covers Sucks. Sorry about the bad pictures my camera wont stay on even with new batteries had to revert to camera phone.
|
Re: 56 Chev Garage build
The bed wood looks nice.
I like the finned rocker covers. Kim |
Re: 56 Chev Garage build
Nice work. Subbed for ideas and progress
|
Re: 56 Chev Garage build
The edelbrock c3bx is a good quality vintage intake let alone much cooler then the chinese junk anyway.
|
Re: 56 Chev Garage build
5 Attachment(s)
I started to run the front brake lines now that my engine was out, and looked at steering out of the firewall. I didn't like it at all so I had asked chuckdriver how much his was out out and used that as a base to cut mine down. Over all I cut roughly 8 inches off the main shaft and 5" out of the outer shaft. If you look at the inner shifter tube I just used a dremmel and ground the 3 spot welds and slid the bracket up the tube and welded the bracket on the outside made it a lot simpler than dissembling the whole colmn just to cut and re weld the inner tube. All I had to do then was to cut the end of tube.
Also I move the neutral safety switch up on the column so it can't be seen inside. |
Re: 56 Chev Garage build
4 Attachment(s)
More tilt column pics mod, also a pic of inner shaft it was beveled welded and cromoly slide over weld and welded again. Can't be to safe once again thanks to Cuckdriver for the measurements!:ito:
|
Re: 56 Chev Garage build
nice work on the column mods :D
i like how you made it work instead of buying a new shiny aftermarket column nice work on your upper radiator hose too we shop at the same hose store :D |
Re: 56 Chev Garage build
Nice work on the column.
Kim |
Re: 56 Chev Garage build
Awesome job Dude! Glad I was able to assist, but you deserve all the credit for pulling it off flawlessly!!
|
Re: 56 Chev Garage build
Nice fab work on column. I took four inches off the outer housing on mine . But i am using stock shifter handle and wanted to get handle further away from dash. Where did you find the shifter handle etc.?
|
Re: 56 Chev Garage build
Shifter Handle is part of the Van Column, I just took the plastic handle tip off and used a aluminum handle dress up kit.
Quote:
|
Re: 56 Chev Garage build
great job
|
Re: 56 Chev Garage build
3 Attachment(s)
re-assembled Tilt, new lower bearing, turn sidnal switch assembly and prepped and primed for paint, steering is nice and tight,got to windy to paint maybe tomorrow! :ito:
|
Re: 56 Chev Garage build
That stand is my cheapo 2 x 4 stud mount, I like it cause I can spin the coulmn to paint easy!
|
Re: 56 Chev Garage build
Looks good.
Nice idea on the paint stand. Kim |
Re: 56 Chev Garage build
Nice stand!!
|
Re: 56 Chev Garage build
cool!!!
|
Re: 56 Chev Garage build
2 Attachment(s)
It wasn't windy yesterday so painted the column no runs! :metal:
|
Re: 56 Chev Garage build
Good progress, I'm going to use your column stand idea!
|
Re: 56 Chev Garage build
It came out nice.
Kim |
Re: 56 Chev Garage build
5 Attachment(s)
Finally rubbed out the paint on the column it came out like glass, The drop for column was machined aluminum so I sanded it with 600 then 1500 grit sand paper and polished by hand. I painted the firewall it had one small run but I am happy with it remember it will be a daily driver can't get to fancy.
P.S. Excuse the quality of the pics still havent bought a new camera yet had to use the phone and it sucks!:ito: |
Re: 56 Chev Garage build
Very shiny.
Kim |
Re: 56 Chev Garage build
1 Attachment(s)
I modified some 61 Imapla lenses to fit my truck tail light housings, Looks sweet but messy work!
|
Re: 56 Chev Garage build
looks good dude
|
Re: 56 Chev Garage build
Nice lights.
Kim |
All times are GMT -4. The time now is 06:19 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com