Re: Show your motor...
 

i want one!!!!!!

Re: Show your motor...
 

A 6BT in a 72 Burb; I have now seen it all:c2:

Anyone like seeing diesel engines in anything check out this site

www.4btswaps.com/

Re: Show your motor...
 

I thought I posted mine,BUT can't find it? My mind is my best friend, I just wish it would visit me more often!! The stock 350 came out of a 68 conversion van that I had & it is hooked up to a 700 trans!

Re: Show your motor...
 

Here is my 500 hp 406. 5.7 gm pm rods, stock crank, Chapman ported Sportsman II heads, stainless rockers, gmpp alum water pump, fully balanced. Is installed in my 70 Longhorn now. Runs hard.

Re: Show your motor...
 

what headers and motormount adapter did you use? are you happy with the clearance? Im in the process of converting my 67 2wd to an lsx. trying to figure out the best way to do it.

Re: Show your motor...
 

They are Doug Thorley Headers and Early Classic Enterprises (ECE) motor mounts. It's the same setup I have on both of my trucks. Clearances are great and both products work as advertised.

Re: Show your motor...
 

Here is the engine I have finished for my 68. It is a Gen 5 454 with original 402 heads, intake & exhaust manifolds, and accessory brackets. I installed a Holley Spreadbore that I rebuilt and I test ran it and made all adjustments on my engine stand, and now am ready to install it in the truck.

Re: Show your motor...
 

Finally got my engine done to the point of needing to install back in the frame.

Went from this,
http://gallery.lisaandmike.org/album...s/PICT4618.jpg

To this,
http://gallery.lisaandmike.org/album...k/PICT5817.jpg

Re: Show your motor...
 

Yeah! Keep em coming

Re: Show your motor...
 

lol srsly? And if it's cranking out 500 why are you running flowtechs with 1.5" primaries. Need more like 1-7/8

Re: Show your motor...
 

BBC 460. Edelbrock aluminum heads. Edelbrock MPFI. Comp hydraulic roller cam. 10:1 compression. Camquest says: 515hp @ 5000; 580tq @ 4000. Going in my 72 K5.

http://www.texas4x4.org/gallery/albu...4000.sized.jpg

Re: Show your motor...
 

Work in progress..

http://420am.net/cheyenne/day1-1.jpg
http://420am.net/cheyenne/day1-4.jpg
http://420am.net/cheyenne/vortecs-4.jpg

350 cid
Edelbrock 650cfm
Edeldrock 1" carb spacer
Edelbrock EPS Manifold
Lunati Bracket Master II Cam / Lifters / Pushrods
Comp Cams Roller Rockers
Comp Cams Double Roller
'906' Iron Vortec Heads

Not pictured..
MSD Distributor Cap/Rotor
MSD Streetfire Wires

I've done about everything I can without pulling the motor. I know if I pull it out I'll tear it completely down and I won't have the money to put it together before summer. This motor was just a O'Reilly's rebuilt motor with maybe 20k on it that I was going to replace a head gasket on.. then replace a head gasket and port and polish the old crap '882' heads on.. then I got new heads, which required a new intake.. Hahaha.. I wonder when I'll be done.

Re: Show your motor...
 

Heres the 454 in my 72 sounds good still have not even drove the damn thing...

Re: Show your motor...
 

I want that!!!

Re: Show your motor...
 

Here's mine, i love showing it off, but next winter she will be apart agaoin.

Re: Show your motor...
 

Green is mt fav color

Re: Show your motor...
 

Sweet thread, I love SBC but how about some 500+ci BBC

Re: Show your motor...
 

68 chevy 350 still under construction

Re: Show your motor...
 

68stepbed, bigsnookmaster,

What engine paint are you two using? those two motors look awsome.

Re: Show your motor...
 

572/620 in my 67 Stepside:

Re: Show your motor...
 

nice!!!

Re: Show your motor...
 

dznucks, I used rattle can touchup paint(MOPAR to match truck color) for my block and heads. The VC's, intake and other bits and pieces, I used DupliColor Cast Coat Iron engine enamel from Advanced Auto Parts.

Re: Show your motor...
 

Fitz thats one bad azz motor

Re: Show your motor...
 

Thanks 68stepbed

Re: Show your motor...
 

..