Re: parting a 72 blazer 4x4
 

I believe '72 is specific to '72. I believe they don't use inners, but just strickly outers because of how the frame horns are in the rear. Thus, the 2 indents in the rear bed crossmember. Randy, should be able to clarify for you for sure.

Back to the thread, Randy, put me down for the transfer case boot, and keep me posted on the console and roll bar. Is the rollbar the more correct factory/dealer hickey bar? I am not real good with blazer parts. Thanks Trevor

Re: parting a 72 blazer 4x4
 

Randy, also would take the pass side floor hold down bracket. When the dust clears let me know about hatch guts, door/jamb pcs, any/all top to body brackets also. Thanks, Harry

Re: parting a 72 blazer 4x4
 

VA72C10, 72 did not have inner brackets, tehy were frame horns like the front ends. These looked fine with bumper, they have been cut on top side to go around body bolt. $35 for set of 4.
Trevor, the boot has one small tear, cannot be seen. I'll give him till tomorrow on the console. The roll bar looks good but I am also unsure about hickey/dealer.
Harry, seat bracket has been spoke for already, sorry. I'll get with you later this week once I find out what everyone wants
Thanks Randy

Re: parting a 72 blazer 4x4
 

182222

Re: parting a 72 blazer 4x4
 

877777777777

Re: parting a 72 blazer 4x4
 

windshield frame is pretty good, only the corners on side that has the plate. No rust in any other corners, one spot on firewall

Re: parting a 72 blazer 4x4
 

97777777777

Re: parting a 72 blazer 4x4
 

2022222222

Re: parting a 72 blazer 4x4
 

207777777

Re: parting a 72 blazer 4x4
 

dsdsds

Re: parting a 72 blazer 4x4
 

OK I basically got it all parted and pics for everyone, please let me know if you want more pics. I'll keep tearing apart some other stuff I have spoken for already. Please let me know what parts you want me to get shipping prices on. Thanks for your patience, Randy

Re: parting a 72 blazer 4x4
 

Whoo doggy!! You tore that thing right up! Don't suppose I could talk you into throwing that battery hold down into my box with the door caps could I? Hmmm?

Re: parting a 72 blazer 4x4
 

I want the intake. Checking on block. Can pick up this weekend.

Re: parting a 72 blazer 4x4
 

Boy randy, you don't mess around! Any thoughts on the tach, gauge cluster, BB extension? Thanks, Eric

Re: parting a 72 blazer 4x4
 

Jeff, got you covered
Daren, I'll get number off block, I don't know if its a 4 bolt or 2
Eric, not sure on tach, ext is $25
Thanks Randy

Re: parting a 72 blazer 4x4
 

block number

Re: parting a 72 blazer 4x4
 

Thanks Randy!!!

Re: parting a 72 blazer 4x4
 

Ok Randy thank you for the good pics of the console with cracks. How much shipped to TX 78015? Price on the roll bar? Shipping is tough though. Will you throw in the ash tray from a diff thread? Thank you.
Posted via Mobile Device

Re: parting a 72 blazer 4x4
 

72Levi, $60 for the roll bar but unsure about shipping. Thanks Randy

Re: parting a 72 blazer 4x4
 

Good price on rb, Ugh give me 1-2 days to work on shipping roll bar, thanks, and waiting on console price.
Posted via Mobile Device

Re: parting a 72 blazer 4x4
 

How much for the door latch reinforcement plates & the wiper arms? & shipping to 49315?
Thanks

Re: parting a 72 blazer 4x4
 

Can you give me an estimate for shipping on the gas tank? I know it's not heavy, but kind of bulky.

Re: parting a 72 blazer 4x4
 

Orange72blazer, pass side reinforcement plate is dinged up quite a bit. $30 shipped for them and original Trico wipers
hgs_notes, total sent
Thanks Randy

Re: parting a 72 blazer 4x4
 

randy,take a scraper to the pad in front of passenger cyl head. (Block deck).Get the #s and code off there..I can tell you what motor is and what year..by the casting # and date that is above the bellhousing by or near the top 2 bell bolts.. I have all the codes in my comp.

Re: parting a 72 blazer 4x4
 

Randy, I'll take the console, thank you, pm sent with info.