Re: Rusty 68 K20 Burb
 

On my 67 to the center of the distributor is 2 3/4 inches.

Re: Rusty 68 K20 Burb
 

Firewall to front edge of core support in center is 39 3/8. Same above headlights 39 3/8

Re: Rusty 68 K20 Burb
 

Thanks so much. Do you have a hei or points dizzy?

That motor is set back in there tight to the firewall, that must be a pain to lift out of there. That is not much room to be able to tip the motor down to get it in too.

So I would assume that the fan shrouds are also different between 2 and 4wd.


Thanks again. The info here is priceless.

Re: Rusty 68 K20 Burb
 

Mine has points thats why I measured to the center. The centerline will not change on either. As far as being tight as long as you can get a screwdriver in to remove the cap it wont really matter. Can't anwser the shroud ? Have the stock v8 one with my burb. My C20 6cyl dosen't have one.

Re: Rusty 68 K20 Burb
 

On another note. I didn't have to scrap the 68 K20. I had a few interested peeps but the solid one fell through the wk I had to make the shell/tub/chassis go away.

A good friend took it, not sure what he is going to do with it, but it found another home.

Re: Rusty 68 K20 Burb
 

Sweet. Good info. Thank you. I think I am going to luck out and maybe have a little more room the a 4x 67-72 frame, but less than similar yr 2wd. We'll see

Re: Rusty 68 K20 Burb
 

What is the measurement to the firewall?

Re: Rusty 68 K20 Burb
 

firewall to radiator support

Re: Rusty 68 K20 Burb
 

Here is where I am measuring from. If that measurement is on the $ then I am close.

Re: Rusty 68 K20 Burb
 

So the gas tank might be able to move slightly forward. The front body mount has room to go forward just enough. I got to lift off the body again to remove the stock 78 K20 Driver rear shock mount that is mounted to the top of my frame. It is in the way of a crossbar.

Re: Rusty 68 K20 Burb
 

You are about 4 inches to far forward.... with your core support

Re: Rusty 68 K20 Burb
 

Fuel filler is on the opposite side too. Not sure what I am going to do about that. Might just hack up a 81-91 burb filler door setup.

Re: Rusty 68 K20 Burb
 

Are you measuring the same spot?

Re: Rusty 68 K20 Burb
 

I measured from the top of firewall by the seal

Re: Rusty 68 K20 Burb
 

I almost had to do this.

Re: Rusty 68 K20 Burb
 

So the neighbor was out of town and let me get a few more measurements. Looks like I am 5" off the mark, and my core support will have to come up too. This puts the front body mount in the way of the upper shackle. I might have to swap in the 52" springs and move the eye hole back sooner than later.

Re: Rusty 68 K20 Burb
 

Just spin the fuel tank around. I did the opposite of you kind of. I put the square body tank in my 69 frame and I just pointed the neck on the tank to the drivers side, so it should work spun around in the square body frame.

Re: Rusty 68 K20 Burb
 

I had thought of that but I never liked the external fuel fill, and for 4x4 purposes, I am worried I might rip it off in the rocks/trees.

Re: Rusty 68 K20 Burb
 

Either way, you should be able to turn the tank around and put the filler on the LH side

Re: Rusty 68 K20 Burb
 

Man this project is moving much slower than I want. Time and $$$ seem to keep going to other things. Life. And a few other broken trucks.

I kinda got to put the body mounts on hold. I got a few other things to consider before I mount it.

I started bolting up a few doors and converting the clamshell setup to barndoors. The doors are pretty beat up, but it's what I got for now.
There is a set for sale on here that even have the correct trim to match. Not the right color, but I lack the trim on my beat up set.

I also need to find front doors, maybe with the odd trim too.

Re: Rusty 68 K20 Burb
 

The doors and hardware came off a burb that had already converted from tailgate to barn door. I am not sure if the hardware like the strickers and stoppers are in the correct spots. I also got this piece of wood as a spacer attached to one door.
Does anyone got pics of the original stuff?

Re: Rusty 68 K20 Burb
 

I got the doors on and somewhat adjusted. They are pretty dented/bent up. The bottom has some rot coming through. I still have the strikers,stoppers, and limit brackets to mount.


If I could find a decent price on some rear glass seals I could almost have it sealed up for the winter.