Re: The Snortin' bull
 

Nice and clean!!!!

Re: The Snortin' bull
 

Thank you, trying to keep it sano. a bit.

Re: The Snortin' bull
 

Gettin close.

Re: The Snortin' bull
 

Thank's again Chizzler. Ya close though still some wiring.Exhaust mock up and build and install. Trans lines. Mount rear shock's. Still got to pull my rear axles and redrill for 5 on 5 and some rear brake work in the drums.

Re: The Snortin' bull
 

Got a couple things done at night during week. Shock lower rear brackets ready to get tacked on. Battery cable terminal ends done. Been busy at work so not to much time at night.

Re: The Snortin' bull
 

finished the tailshaft of transmission .Speedo all hooked up.

Re: The Snortin' bull
 

The batterie's are all wired in now.Finishing up harness of truck.Got interior wired,Back lighting wired in for guage packs,Exterior lighting wired.Alternator wired.

Re: The Snortin' bull
 

Working on the rear lighting harness.This truck had a handful of hole's in dash and everywhere.I filled them various period style switches instead of filling them.Keepin' the theme.

Re: The Snortin' bull
 

Diggin in part's boxe's I had an old school fill neck. From a 30"s Studebaker. For now it'll work.Set in the wood in the bed to mock up fill neck.

Re: The Snortin' bull
 

Thank's tryin' to keep it simple and clean.

Re: The Snortin' bull
 

Through out this project rust is in the way as it for most of us.This stuff is the fashnizz. Aerokroil none better work's like a champ.

Re: The Snortin' bull
 

Even though this truck will look like a road side left over little detail's like ugly windshield squirter's bugged me..Found some original style on a parting out truck in the paper.The little round head one's are now on the hood.

Re: The Snortin' bull
 

Turn signal lever I modded. This might mess with some folk's . Back in the fiftie's rodder's would flip the shifter to left of the column.

Re: The Snortin' bull
 

A license frame from the sixtie's in Seattle . The gmc in red matched the lettering on the tailgate of the truck.

Re: The Snortin' bull
 

The red positive battery cable stood out.Used some old school asphalt loom to blend it in under the hood.The loom is cool stuff.Using it in other area's also.

Re: The Snortin' bull
 

Got my seat belt's and anchor plate's from Juliano's today. Started to install. There will be belt's also for a center passenger.Sorry about the grainy pic's.

Re: The Snortin' bull
 

Looks good.

Re: The Snortin' bull
 

Thank you., Appreciate the comment.

Re: The Snortin' bull
 

Got my gas cap and fill neck today from BAM Manufact..Look's and fit's better than my temporary set up.

Re: The Snortin' bull
 

Good progress. like that gas cap setup. Clean

Re: The Snortin' bull
 

Thanks Chizzler,I thought the same.not to plain not to fancy.

Re: The Snortin' bull
 

These seat belt anchor plate's from Juliano's are a must.I have seen a lot of pulled thru washer's people have used on the floor of vehicle's..

Re: The Snortin' bull
 

Belt's are in.

Re: The Snortin' bull
 

1960 GMC dash from the backside.It is need of some help .Had to make a jumper for 12 volt as the Circuit board has deteriated over time. Really only need it for backlighting the speedo.

Re: The Snortin' bull
 

After some clever rewiring and mating to American Autowire harness and the correct style bulb sockets (pc) style we have lighting for the gauges and hi beam indicator also working. Gas guage also. Mounted actual lh and rh signal lamps in dash. Installed an under dash courtesy light with a switch on the passanger side.