Re: the panelburb getting cut up
 

Grille hoops still available?

Re: the panelburb getting cut up
 

sorry they are gone

Re: the panelburb getting cut up
 

Do you have Rh and Lh of the full cut from Front angle to bolt hole where the b-pillar locates?
Attachment 1990301









.

Re: the panelburb getting cut up
 

I will take a look tomorrow and let you know what i do have

Re: the panelburb getting cut up
 

Dwayne
Nothing left in that area. If I end up cutting up one of the others I will contact you. will send pm on the other stuff

Re: the panelburb getting cut up
 

Got the PM Richard
Thanks for looking.












.

Re: the panelburb getting cut up
 

Are the bottom latches for the barn doors available?
Price on grille?

Re: the panelburb getting cut up
 

Let me take a look, I think i still have a set left. The grill I will have to look at as well. I seem to remember it being rusty and I know the trim is gone off of it.

Re: the panelburb getting cut up
 

I need one of the core support mounts thats riveted to the front of the frame
please pm me with price and PayPal address if you can help.
thanks

Re: the panelburb getting cut up
 

I do have some. Do you need 67-68 or 69-72? they are different

Re: the panelburb getting cut up
 

How much for the engine stands and power steering pump to Elberton ga 30635

Re: the panelburb getting cut up
 

let me get the pump pulled off and see if it will all fit in a large flat rate. You did see that there is no engine mount with the pump and the stands are big block, correct?

Re: the panelburb getting cut up
 

I Did, does the pulley have a part number on it?

Re: the panelburb getting cut up
 

Hey Richard - I am looking for both sides, tail light housings and around the side. Any good, straight, rust free ones?

Re: the panelburb getting cut up
 

you talking like this? Some dents but I don't think there was any rust on them. I can pull them out and get current pics if interested

.

Re: the panelburb getting cut up
 

Yep, don't need the side marker lights (working on the 67) so a cut at the edge may make it easier to ship

Re: the panelburb getting cut up
 

ok will pull them both out shortly and post pics.

Re: the panelburb getting cut up
 

Both of them have dents in the outer sheet metal but zero rust. I circled the dents with white pencil to make it easier to see. I also drew a line where I think you wanted them cut? The one has some rot out on the inner pillar section that is still attached to it but should not affect what you are needing. Let me know if you think they will work for what you want. If so PM me your address so I can get a full total of what they would run ya

Richard

Re: the panelburb getting cut up
 

couple more pics

.

Re: the panelburb getting cut up
 

Thanks Richard.

They may be worse than what I have. Let me get back to the body shop and see what they think and I will reach back out. I will also PM you my new address.

-Paul

Re: the panelburb getting cut up
 

Did anyone take the 3rd door, do you have any of the 3rd hinges , I also read were you might be cutting another one up, id like to purchase a b piller for 3rd door

Re: the panelburb getting cut up
 

I do still have the door but the hinges are already gone. No B pillars at this time either, sorry

Re: the panelburb getting cut up
 

Do you still have the side marker lights?

Re: the panelburb getting cut up
 

3 of the 4 are still on the burb. Not sure where the 4th one got to but I can look around to see if I can find it. Honestly they are not in Very good shape. Will post a few pics later

Re: the panelburb getting cut up
 

here are pics of the mounts