![]() |
Re: LS1 into a 73 cheyenne
Quote:
|
Re: LS1 into a 73 cheyenne
4 Attachment(s)
So i finally got my ignition wires there Taylor 409 10.4mm with a 135* boot
|
Re: LS1 into a 73 cheyenne
4 Attachment(s)
here a pic of the complete set up
|
Re: LS1 into a 73 cheyenne
that is SICK! looks really good man! :metal:
|
Re: LS1 into a 73 cheyenne
Couldnt agree more with Dennis. That is one awesome looking engine. Hope you will take all the pretty stuff off before trying to set it in the chassis to avoid any damage.
|
Re: LS1 into a 73 cheyenne
All I can say is....................... WOW that is one beautiful setup. Those covers give it a classic look! Keep the pics coming. Nice progress.
|
Re: LS1 into a 73 cheyenne
Quote:
|
Re: LS1 into a 73 cheyenne
5 Attachment(s)
This is my fuel line set up. I decided to go with a single line filter regulator. I used Jegs braided 6 AN female 2ft. ready made hose. 3/8 and 5/16 tubing with Swagelock compression fittings 2- 3/8 to 6AN males and 2- 5/16 to 6 AN males. At the regulator I used 1- 3/8 and 1- 5/16 Swagelock compresion to compresion fittings and a GM O-ring X 6AN.
|
Re: LS1 into a 73 cheyenne
5 Attachment(s)
No progress on my truck since I been busy finishing off my uncles truck. Cab fire wall and chassi have been painted. We used PPG Atomic Orange (code 83), and PPG 2021 clear. A high gloss on the chassi. We were goin to drop in an LS1 this Sunday but the paint was still sticky, will try again this week end.
|
Re: LS1 into a 73 cheyenne
4 Attachment(s)
few more
|
Re: LS1 into a 73 cheyenne
Looking good. That color looks cool.
|
Re: LS1 into a 73 cheyenne
I love that color! This is what I was going to paint my 68. I even had a little design figured out that I was going to have airbrushed on a lower corner of the tailgate...... an orange that was split open at the top, with a mushroom cloud coming out of it. :D
|
Re: LS1 into a 73 cheyenne
Man that egine looks sick, you guys give to many ideas and my bank keeps laughing at me, lol. Keep it up...
|
Re: LS1 into a 73 cheyenne
Quote:
|
Re: LS1 into a 73 cheyenne
what paint did you use on the frame?
|
Re: LS1 into a 73 cheyenne
Quote:
|
Re: LS1 into a 73 cheyenne
Quote:
|
Re: LS1 into a 73 cheyenne
wow:metal:
i just now came across this thread.....wow:metal: |
Re: LS1 into a 73 cheyenne
1 Attachment(s)
Quote:
|
Re: LS1 into a 73 cheyenne
smokedat, the engine looks awesome but the cab and frame are even better. NICCCCCE!
|
Re: LS1 into a 73 cheyenne
Quote:
Thanks for the compliments, will also color match the rally wheels. |
Re: LS1 into a 73 cheyenne
1 Attachment(s)
Check out my new avatar :metal:
|
Re: LS1 into a 73 cheyenne
Update, I started to gather some of the paint supplys I got the clear 2 gallons of Dupont Imron, yes the stuff that got outlawed in Cali. Game plan I will start by removing the front clip to get to the old 350 pulling it out, strip interior, remove cab and bed, clean the frame, paint the frame, then work on the exterior body bringing it down to bare metal, tubbing the rear drop in a Ford 9", install 4 link, paint exterior, then finally drop the LS, wire the new set up, run new wet lines, list goes on and on...This swap has been past due as I was suppose to move on Feb, but escrow got delayed, so i will start the swap after i move hopefully by the end of this month.
|
Re: LS1 into a 73 cheyenne
I had a supra back in the day that i painted that color...very nice color!
|
Re: LS1 into a 73 cheyenne
1 Attachment(s)
This is my body and paint material,
|
Re: LS1 into a 73 cheyenne
1 Attachment(s)
Dupont Imron 500S Clear
|
Re: LS1 into a 73 cheyenne
..
|
Re: LS1 into a 73 cheyenne
...
|
Re: LS1 into a 73 cheyenne
..
|
Re: LS1 into a 73 cheyenne
I will be fabricating custom aluminum accesories for interior
|
Re: LS1 into a 73 cheyenne
2 Attachment(s)
sterring wheel and honker
|
Re: LS1 into a 73 cheyenne
1 Attachment(s)
Will fabricate a dash panel for my gauges and the trim piece for the dash
|
Re: LS1 into a 73 cheyenne
3 Attachment(s)
Pedals that I fabricated still need to be cut drilled and pilished
|
Re: LS1 into a 73 cheyenne
4 Attachment(s)
fabriceted this catch can still in progress but heres a pic
|
Re: LS1 into a 73 cheyenne
Nice build.......and pics
|
Re: LS1 into a 73 cheyenne
im interested in seeing how those pedals turn out.
|
Re: LS1 into a 73 cheyenne
Man I miss the old school IMRON. The switch to the low VOC IMRON 5000 was a beating back when it come out in the mid 90's. You almost couldn't make it dry. The IMRON 6000 low VOC base/clear had an awesome cross linking clear (99S, IIRC) that flowed like glass, and fast, too. I think they outlawed that everywhere, though.
The only bad thing you will find with the IMRON is that it is like sanding a rock if you have to go back and color sand it. |
Re: LS1 into a 73 cheyenne
Quote:
|
Re: LS1 into a 73 cheyenne
Quote:
|
Re: LS1 into a 73 cheyenne
great
|
All times are GMT -4. The time now is 02:12 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com