Re: Cabs for patch panel cuts
 

I can probably do the drivers side but not sure about passengers side. I will have to look after work and let you know.

Re: Cabs for patch panel cuts
 

The stuff that was apart didnt have good pieces,I think there are some good ones but I have to take more stuff apart to get them including the cab Im taking off my truck. I can Pm you when it happens but Im not sure how soon it will be. How bad do you need them?

Re: Cabs for patch panel cuts
 

Looking for good uncut AC dash. Have anything?

Re: Cabs for patch panel cuts
 

Sorry only one uncut dash left and its non AC

Re: Cabs for patch panel cuts
 

Need good uncut AC dash. Anything?

Re: Cabs for patch panel cuts
 

Sorry. Didn't see message.

Re: Cabs for patch panel cuts
 

How much for the non-AC dash shipped to 14036.

Re: Cabs for patch panel cuts
 

Anytime been lookin for a while!!

Re: Cabs for patch panel cuts
 

The last one went to louisiana I think and it cost $60 to ship it but your considerably closer so Id like to believe it would be less. I actually have two, one is completly uncut the other is mostly uncut. Id like to get $60 for the completly un cut but I would go $40 for the mostly uncut. Mostly uncut consists of the rectangular radio hole is complete but some one cut slots between the center and the knob holes. It would show with an origanal radio but if you had something that was aftermarket that had a face plate it wouldn't show. I can post a picture of that one tomorrow. The uncut one is not here at my house and would take a few days to get a chance to go retrieve it. Where do you want to seam it? If you do it under the dash pad I can do better on the price and the shipping. Lmk Frank

Re: Cabs for patch panel cuts
 

I'll see what I can do to speed up the progress.

Re: Cabs for patch panel cuts
 

still have some stuff

Re: Cabs for patch panel cuts
 

Do you still have the pieces you cut off for loosecannonzs that he didn't want? If so how to 70737?
Posted via Mobile Device

Re: Cabs for patch panel cuts
 

What pieces do you need? I have a corner for the passengers side that was a bit too small for him to use. That 's the only thing he didn't take,I cut a bigger one from something else. I have stuff to cut up yet though just let me know what you need and I'll see what I can do.

Re: Cabs for patch panel cuts
 

Now looking at the pick it looks a little short for me too. I really need both driver and passenger side like you cut in post#56

Re: Cabs for patch panel cuts
 

Are you fixing rot or dents? Give me some measurement of what you are looking for and Ill send you pictures of what I have left.

Re: Cabs for patch panel cuts
 

Was the someone else me?

Re: Cabs for patch panel cuts
 

No he is looking for some upper cab corner patches,I had a piece I cut out before but it was too small. The parts you want are still on the cab of my truck that I havent been able to take apart yet or finish my new cab either. Im a self employed contractor and a couple of jobs that I took turned out to be completly destroyed well above the job scope with powder post beetles ,ants and water damage. Good job security but made it hard to get work done at home.

Re: Cabs for patch panel cuts
 

Ok after I measured it looks like the piece in Post#51 will work. I am going to hold of on the drivers side for now. Is this piece dent free on the body lines? If so how much to ship it to 70737?

Re: Cabs for patch panel cuts
 

I'll double check for dent and I'll get that figure for you later today

Re: Cabs for patch panel cuts
 

I dont see any dents on the body lines. The estimate for fed ex is $20 for 3 day ground and the other corners I sold like that I got $35 plus shipping but If you want it I will do $50 shipped.

Re: Cabs for patch panel cuts
 

Sorry for the delay do you still have the piece above?
Posted via Mobile Device

Re: Cabs for patch panel cuts
 

Yes I do.

Re: Cabs for patch panel cuts
 

Can you send me payment info?
Posted via Mobile Device

Re: Cabs for patch panel cuts
 

Sent you a PM