The 1947 - Present Chevrolet & GMC Truck Message Board Network

The 1947 - Present Chevrolet & GMC Truck Message Board Network (https://67-72chevytrucks.com/vboard/index.php)
-   Squarebody Projects and Builds (https://67-72chevytrucks.com/vboard/forumdisplay.php?f=139)
-   -   Used Parts Build (https://67-72chevytrucks.com/vboard/showthread.php?t=638991)

tinydb84 07-24-2015 01:24 AM

Re: Used Parts Build
 
http://i20.photobucket.com/albums/b2...723_190533.jpg
http://i20.photobucket.com/albums/b2...723_190711.jpg

I am also pushing the engine back further. I am going to clearance the firewall a hair. Bad picture but check out where the first cylinder is compared to the front wheel center line. In total the engine is back 3 inches from the stock position.
http://i20.photobucket.com/albums/b2...723_205023.jpg

77K10Silverado 07-24-2015 02:58 PM

Re: Used Parts Build
 
Gracious! LS fever!!

Hankster 07-25-2015 03:05 PM

Re: Used Parts Build
 
Engine looks good sitting in there,

tinydb84 08-02-2015 11:57 PM

Re: Used Parts Build
 
Quote:

Originally Posted by 77K10Silverado (Post 7252449)
Gracious! LS fever!!

LS swap everything! (well eventually...)

Quote:

Originally Posted by Hankster (Post 7253435)
Engine looks good sitting in there,

Thank you sir.

tinydb84 08-02-2015 11:57 PM

Re: Used Parts Build
 
Started on my trans crossmember. I am thinking I might try to make something kinda like the Porterbuilt center section (but poorer and uglier....we'll see where that ends up).
http://i20.photobucket.com/albums/b2...801_184113.jpg
Was going to use the old mount but later decided against it.
http://i20.photobucket.com/albums/b2...801_202615.jpg
I always jig everything perfect and forget to prep the area to weld first...
http://i20.photobucket.com/albums/b2...802_182134.jpg
Since I was looking at the "mig like tig" thread earlier
http://i20.photobucket.com/albums/b2...802_184106.jpg
Dropped some weld into the channel of the backside
http://i20.photobucket.com/albums/b2...802_184928.jpg
So far
http://i20.photobucket.com/albums/b2...802_185753.jpg
Cut my next piece of tube and realized the company sent me 1.75'' end pieces so thats as far as I am going to get today.

Justin@EntropyRad 08-03-2015 10:04 AM

Re: Used Parts Build
 
coming along nicely

tinydb84 08-09-2015 11:36 PM

Re: Used Parts Build
 
Quote:

Originally Posted by Justin@EntropyRad (Post 7262209)
coming along nicely

Thank you sir.

Finished the crossmember for now. Ordered more tabs and bent tube to start the frame stiffener.
http://i20.photobucket.com/albums/b2...806_192725.jpg

tinydb84 08-09-2015 11:38 PM

Re: Used Parts Build
 
Started drilling the holes for my crossmember and decided to work on something else (I hate drilling holes).
Decided to cut my tunnel up to use it to create the new tunnel.
http://i20.photobucket.com/albums/b2...809_141723.jpg
http://i20.photobucket.com/albums/b2...809_142616.jpg
Ended up moving it back and triming the front part back then made a filler plate in the center. Looks like I am only adding about an inch or so in height and most of it in the center.
http://i20.photobucket.com/albums/b2...809_180839.jpg
Tried to make a filler piece that matches the original floor.
http://i20.photobucket.com/albums/b2...809_191300.jpg
Where I left it for now
http://i20.photobucket.com/albums/b2...809_191321.jpg

tinydb84 08-11-2015 12:30 AM

Re: Used Parts Build
 
More metal shaping...I get why the professionals charge so much!
http://i20.photobucket.com/albums/b2...810_191449.jpg
http://i20.photobucket.com/albums/b2...810_194408.jpg
Got low on gas so I pulled my tank to exchange it while I'm at work tomorrow since the welding shop is a couple blocks away
http://i20.photobucket.com/albums/b2...810_194704.jpg
Sooooo since the tank was off, I used it to make some bends. I really want a shrinker/stretcher!
http://i20.photobucket.com/albums/b2...810_200009.jpg
But what do I do with it now....jk
http://i20.photobucket.com/albums/b2...810_201153.jpg

tinydb84 08-11-2015 12:30 AM

Re: Used Parts Build
 
Then I saw this....
http://i20.photobucket.com/albums/b2...0-13-01-29.png
So I bought one for my 66. Didn't need it now but couldn't pass up the deal...

tinydb84 08-14-2015 02:15 AM

Re: Used Parts Build
 
I took today off just to work on my truck (I never take days off). Thought I would have got more done....
http://i20.photobucket.com/albums/b2...813_123956.jpg
http://i20.photobucket.com/albums/b2...813_153712.jpg
Once I did one side the second took half the time
http://i20.photobucket.com/albums/b2...813_165001.jpg
I was running stringers and totally forgot about stitch welding. This looks much better than my stringers. Too bad I didnt think of it until I was almost done...
http://i20.photobucket.com/albums/b2...813_183528.jpg
All done with the rear. I will start on the front this weekend. More curves....yay...
http://i20.photobucket.com/albums/b2...813_194156.jpg

tinydb84 08-16-2015 10:20 PM

Re: Used Parts Build
 
Wasted a bunch of time trying to make one piece to fit the front of the tunnel before just patching it. Working extra slow...
http://i20.photobucket.com/albums/b2...816_170502.jpg
Got my front bars in. Here is what I am thinking of doing.
http://i20.photobucket.com/albums/b2...815_195733.jpg

tinydb84 08-23-2015 10:29 PM

Re: Used Parts Build
 
Look at this monstrosity!
http://i20.photobucket.com/albums/b2...823_182427.jpg

Hey at least it is done! Now I am going to strip the floors (top and bottom) and epoxy everything...Next weekend lol

tinydb84 08-23-2015 10:30 PM

Re: Used Parts Build
 
Started my welding class. Got about 10 of these:
http://i20.photobucket.com/albums/b2...820_204654.jpg
and all the students work:
http://i20.photobucket.com/albums/b2...820_204648.jpg
There are 15 MIG's, 4 O/A, 10 Stick, and a ton of metal fab stuff.
Didnt get a pic of the rest of the shop but check out their machine shop class...
http://i20.photobucket.com/albums/b2...818_200354.jpg
I am going to take that next semester.
Then I bought this so I can practice between classes:
http://i20.photobucket.com/albums/b2...822_160332.jpg

tinydb84 08-31-2015 12:37 AM

Re: Used Parts Build
 
Finished welding my floor, stripped it, and painted it.
http://i20.photobucket.com/albums/b2...830_171901.jpg
http://i20.photobucket.com/albums/b2...830_181908.jpg
http://i20.photobucket.com/albums/b2...830_185851.jpg

It got dark before I could paint so I fish plated my notches since I hadnt got around to doing it. I had a bunch of 1/4'' steel...a bit over kill but whatever. Since I already was mixing paint I figured I'd paint them since I work slower than rust....
http://i20.photobucket.com/albums/b2...829_202755.jpg
http://i20.photobucket.com/albums/b2...829_221904.jpg
http://i20.photobucket.com/albums/b2...829_222625.jpg
http://i20.photobucket.com/albums/b2...830_171836.jpg

tinydb84 09-05-2015 11:24 PM

Re: Used Parts Build
 
Not much of a pic but it feels great to actually put something back together. The carpet almost fits. Need about an inch or so on the side but it is good enough to use the original one for now.
http://i20.photobucket.com/albums/b2...905_190245.jpg

tinydb84 09-08-2015 01:22 AM

Re: Used Parts Build
 
No cool pictures but since it was 95 degrees out today I figured I'd do more dirty work.
http://i20.photobucket.com/albums/b2...907_183314.jpg
http://i20.photobucket.com/albums/b2...907_210529.jpg
Not perfect but I stripped the bottom of my cab and painted it in epoxy. The hvlp gun didnt like the angles so I am sure it is spotty and has runs but for the underside of my cab I am fine with it.

tinydb84 10-04-2015 12:35 AM

Re: Used Parts Build
 
Started to redo my motor mounts. I didnt want to build a bridge to the upper control arm and make it look half assed.
http://i20.photobucket.com/albums/b2...003_152658.jpg
I have been having a ton of problems with my Alphatig. I just sent a request to return it through Amazon. All I can tell is that there is a gas problem. Tried all kinds of thing but it randomly has a flow or contamination issue...
http://i20.photobucket.com/albums/b2...003_203756.jpg
Then....
http://i20.photobucket.com/albums/b2...003_203747.jpg
Ended up using my mig to finish it. Really pissed that I spent all that time perping everything to then mig it....
http://i20.photobucket.com/albums/b2...003_205306.jpg

tinydb84 10-12-2015 12:18 AM

Re: Used Parts Build
 
Did a bit of work on my mounts. Will probably add a bit to the bottom just for looks.
http://i20.photobucket.com/albums/b2...011_190047.jpg

tinydb84 10-13-2015 02:09 AM

Re: Used Parts Build
 
Finished my motor mounts. Had to move over my steering bracket from my last mounts:
http://i20.photobucket.com/albums/b2...012_214740.jpg
Was wondering if I could still mig. Havent done it in so long.
http://i20.photobucket.com/albums/b2...012_214239.jpg
Just need to paint them.
http://i20.photobucket.com/albums/b2...012_214723.jpg

slammed427 10-13-2015 11:30 AM

Re: Used Parts Build
 
Love the work! I'll be following along.

tinydb84 10-18-2015 02:56 AM

Re: Used Parts Build
 
Quote:

Originally Posted by slammed427 (Post 7339831)
Love the work! I'll be following along.

Thanks. Hopefully I can pick up the pace a bit.

tinydb84 10-18-2015 02:57 AM

Re: Used Parts Build
 
Painting everything today. The gun broke in the middle so ignore the runs in the paint...
http://i20.photobucket.com/albums/b2...017_170226.jpg
http://i20.photobucket.com/albums/b2...017_170204.jpg
http://i20.photobucket.com/albums/b2...017_170123.jpg

tinydb84 11-18-2015 01:24 PM

Re: Used Parts Build
 
I didn't really like the weld I did on the bottom of my SFBD. It didn't look up to my standard but I didn't fell comfortable just grinding it smooth. So I came up with this:
http://i20.photobucket.com/albums/b2...107_154341.jpg
and welded them to the frame:
http://i20.photobucket.com/albums/b2...107_154406.jpg
http://i20.photobucket.com/albums/b2...107_154423.jpg
Did three of them on each side. Should be solid as can be.
Then I didn't like the por15 on there. It was starting to peal in some areas (and rock hard in others). It seemed like if you hit it just right it would come off. So instead of worrying about it I stripped it all off and shot it with epoxy instead.
http://i20.photobucket.com/albums/b2...118_080502.jpg

Going to toss the engine and trans back in. Going to change the trans mount a bit (because I don't feel like drilling that many holes). Then start on the rear.

tinydb84 11-30-2015 10:32 PM

Re: Used Parts Build
 
Engine in and clip on!
http://i20.photobucket.com/albums/b2...129_135334.jpg
http://i20.photobucket.com/albums/b2...123_155750.jpg
Gotta make an adjustment on the trans mount and pull the bed next week I hope.


All times are GMT -4. The time now is 07:05 PM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com