Re: My 1962 C10 Build Thread "Grandpa's Truck "
 

Got the hinges worked on yesterday...they were all sloppy..a few hours and a few minutes of frustration finding the parts..I came up with these from Dorman part #38374, its a kit assortment and has 2 of the ones for the 62 ..so I bought as many as I could they only had 2 at one parts house and one at another...then found them at Pep Boys availible seperate but for the same price as the assortment, at 6$ per set its not bad and LMC wanted 9.99 plus their shipping would have been more

I cleaned them up and re used the pin and put a good coat of anti sieze on the pins when I installed them, all hinges like new for under 30$

Re: My 1962 C10 Build Thread "Grandpa's Truck "
 

Got some primer surfacer shot today and all the seams sealed

Re: My 1962 C10 Build Thread "Grandpa's Truck "
 

big difference in this and what I started with

Re: My 1962 C10 Build Thread "Grandpa's Truck "
 

more

Re: My 1962 C10 Build Thread "Grandpa's Truck "
 

looking good.i know what you have went through doing this cab sheet metal work i restored a 66 truck back in 1994 and most of the repair panels were not available then and had to be made from scratch including the inner rocker panels.looks like you have done a fine job.

Re: My 1962 C10 Build Thread "Grandpa's Truck "
 

That must have been fun, I had to make my own share of patches, I made both inner rockers and the RH floor patch, as well as the corners of the knee knocker cab below the windshield, also made several patches for the hood, Its been a long road..I hope it lasts another 49 years after all this !

Re: My 1962 C10 Build Thread "Grandpa's Truck "
 

Got one more door painted inside and the rebushed hinges painted

Re: My 1962 C10 Build Thread "Grandpa's Truck "
 

more

Re: My 1962 C10 Build Thread "Grandpa's Truck "
 

got the summit headers test fitted...they look ok...kinda cheap and thin flanges, but for 200$ what do u expect ?

Re: My 1962 C10 Build Thread "Grandpa's Truck "
 

Good to see you back :)....it's been almost a year.

Do you have a part number for those headers? How far down do they hang underneath?

Re: My 1962 C10 Build Thread "Grandpa's Truck "
 

Subscribed, went through the first couple pages, very nice workmanship

Re: My 1962 C10 Build Thread "Grandpa's Truck "
 

Made a new trans x member today and started on the exhaust system

Re: My 1962 C10 Build Thread "Grandpa's Truck "
 

Thnaks so very much ! I really appriciate it =)

Re: My 1962 C10 Build Thread "Grandpa's Truck "
 

Yeah went back to work full time and the hiurs are long on top of a long commute, but I had a few days off and got back to the 62 !

The headers are summit long tubes for a 67 camaro , they were 239 $ as I recall, they dont hang too low and for a stock truck like mine plenty of clearance, I can get the part # if you want in a few

Re: My 1962 C10 Build Thread "Grandpa's Truck "
 

pics

Re: My 1962 C10 Build Thread "Grandpa's Truck "
 

pics 2

Re: My 1962 C10 Build Thread "Grandpa's Truck "
 

finished my exhaust tonight, sounds awesome !!

Re: My 1962 C10 Build Thread "Grandpa's Truck "
 

tail pipes, 2.50 mandrel bent pipe

Re: My 1962 C10 Build Thread "Grandpa's Truck "
 

Re: My 1962 C10 Build Thread "Grandpa's Truck "
 

got my belt set up at the pick n pull.....bastards charge an arm and leg for this stuff now!

I am adding AC and needed to relocate the alt to the other side, got a 90s camaro belt set up

Re: My 1962 C10 Build Thread "Grandpa's Truck "
 

Been a while but still working on the 62, been going slow but..the vintage air ac is in and the upper intake is powder costed as well as all accy brackets and pulleys, I get a deal thru work so its better than me cleaning and using a rattle can, cleaning up the engine bay as I go till I blow the body apart and the front clip comes off for paint

Re: My 1962 C10 Build Thread "Grandpa's Truck "
 

pics won't load for some reason

Re: My 1962 C10 Build Thread "Grandpa's Truck "
 

before, I swapped this engine in when I was 17...I just wanted it to run at that time...engine was hi tech then ! I still like the look of the TPI !

Re: My 1962 C10 Build Thread "Grandpa's Truck "
 

Nice work. subscribed.

Re: My 1962 C10 Build Thread "Grandpa's Truck "
 

not much progress...just doing the easy stuff and thats spending money !

bolts and door parts back from plater today !