Re: My 86 build
 

nevermind...no longer available.

Re: My 86 build
 

I'll have to check em out.

Re: My 86 build
 

I've been having trouble with my truck blowing fuses during start up, and the other day it would not start at all so I had to short it acrosss the terminals to get it to start. So I picked this up today, another early Christmas gift!

Re: My 86 build
 

Got my new starter on today. It was quite an ordeal, but I got it on and running, still needs a shim or two. I think my flexplate is bent and theres a few teeth that are burred up. I'll work on that later, but at least it starts again.

Re: My 86 build
 

got an email back from Nate....seriously thinking about a Porterbuilt rear dropmember!

Re: My 86 build
 

I talked to Nate on the phone this evening, he cleared up a few questions that I had on the rear dropmember.....now it's up to me to decide! I think I'm gonna go with weld in version instead of the bolt in, it's a little cheaper and I'm guessing alot cleaner looking, but the bolt in kit does have its advantages.

Re: My 86 build
 

cool

Re: My 86 build
 

Hey, awsome job so far. I really like the dash. Would you mind sending me a PM so I can get some more infor on how to do it? I really need to get mine cleaned up.

Thanks.

Re: My 86 build
 

sure no prob.

Re: My 86 build
 

These are the only pics I have of my dash. I didn't take any pics while I was doing it, only after it was done. The fist one is after the fiberglass, I just painted it black to see how it would look one colour. You can see how rough it looks before the bondo.

Re: My 86 build
 

Great Build so far! keep up the great work!

Re: My 86 build
 

I haven't been doin much lately, just gathering parts!

Re: My 86 build
 

i'm in the same boat :P

Re: My 86 build
 

...too good to pass up. now I have to order some for the back.

Re: My 86 build
 

Do you have any pics of your front bag set up

Re: My 86 build
 

a couple of pics. Dominator 2600 bags, homemade 1/4 " steel plate for top and bottom mounts. sorry about the rust and dirt, but it is my DD.

Re: My 86 build
 

thanks fam & rust happens..lol

Re: My 86 build
 

Question I plan on bagging the front of my truck here soon , I have the same bags as you and the eBay plates. How do you have your airlines run in the front. (as in were they go into the bag)

Re: My 86 build
 

I drilled a 1" hole on the back side of the spring pocket which the air line goes though, ( I have a 1ft piece of fuel line hose over the air line to protect the air line from wear) to a 90* push to connect fitting. The air lines are run up to my rad support to a tee.

Re: My 86 build
 

Just ordered a set of tires for the back today.....Goodyear Eagle F1 GS 245/45/18. $365 a piece + tax!....on backorder till march, and I should have my fronts in the next few days.. my buddy got them for me from a guy he works with for $200.

Re: My 86 build
 

haha i knew from the thread pattern it was gy eagle gt's :lol: ive been working at goodyear for too long now..

but how much did you pay for them?

Re: My 86 build
 

small world.....my buddy also works at Goodyear in Napanee..$200 for the pair

Re: My 86 build
 

I think that's cheaper then cost. How'd you get it soo cheap?
Posted via Mobile Device

Re: My 86 build
 

Man thats like a short rive fro here! Where you located?

Re: My 86 build
 

I live in Renfrew, but my bud lives in Napanee.