Re: What did you do to your truck today part IV
 

forestb if you can get away with it I think it's awesome.

Re: What did you do to your truck today part IV
 

I also was able to drive the truck for the first time on the freeway with the new 700r4. Vary happy 😊
Posted via Mobile Device

Re: What did you do to your truck today part IV
 

Finally got the engine back together with the new camshaft kit from CompCams. Nothing wild, just a replacement for the worn out one that left me stranded last month.

Re: What did you do to your truck today part IV
 

http://67-72chevytrucks.com/vboard/s...4&postcount=90
^installed new cam kit

SHE'S ALIVE!!! https://youtu.be/26ZDzVYPUbw
After realizing i put the dizzy in backwards again, did the same thing for the first engine start up, she fired right up. We ran her through the COMPCams break-in procedure with only one hiccup. I hadn't fully tightened the distributor after spinning it around and it walked the timing way back to where it was backfiring real bad. I tighten it back down in the right spot and ran her 25 min between 2000-3000rpm, varying ever few minutes.

Re: What did you do to your truck today part IV
 

Installed the Sissy Box under the dash.......

Re: What did you do to your truck today part IV
 

Ooh! I want me one of those! Did I mention, I am female :) Seriously, I have not seen such a thing. Is it a factory Kleenex box? My mother has this obsession with always having tissues available, that would be just the ticket. Where did you get it?

Re: What did you do to your truck today part IV
 

This is a quick search on eBay, where I found mind. if you have a Chevy, they have them with the proper badges, but nothing technical correct for GMC, so I found a generic one with no badging. The make a few styles, you need to look for a "swing out" type, they make a pull out type but it would mount to the underside of our dashes.

http://www.ebay.com/itm/VINTAGE-ORIG...VZKkNb&vxp=mtr


http://www.ebay.com/itm/Vintage-Klee...FY2s-n&vxp=mtr


https://www.ebay.com/sch/i.html?_odk...enser&_sacat=0

Use this search string terms "vintage 195* tissue dispenser"

Re: What did you do to your truck today part IV
 

Got the engine in last night.

Re: What did you do to your truck today part IV
 

Installed a cup holder.Attachment 1667072

Re: What did you do to your truck today part IV
 

lacquer the wood boardsAttachment 1667170

Attachment 1667169

Attachment 1667168

Re: What did you do to your truck today part IV
 

Ha! You're doing exactly the same thing I am doing this week.

I got my wood from Mar-K and it's Pecan.

It takes forever though, staining it with the spar... thinning down the first few coats and then putting pull strength coats on, each side.

It's been taking at least 12 hours for each coat to dry (the thinned coats are drying faster, of course).

Re: What did you do to your truck today part IV
 

I replaced the rockers on my pickup. They turned out good, but I'm glad I don't have to do that again!

Re: What did you do to your truck today part IV
 

Replaced the master cylinder after 2 years of pumping brakes.
Flushed and bleed them 2 days ago with fresh BF and then replaced MC this morning. Stops awesome now!

Re: What did you do to your truck today part IV
 

replaced the mechanical fuel pump with an electronic one....because I thought I needed a new fuel pump. Turns out, I was just out of gas. Didnt realize how much gas would evaporate from not driving it for 2 months.

Re: What did you do to your truck today part IV
 

thats funny!!! glad I am not the only one

Re: What did you do to your truck today part IV
 

Installed the aluminum radiator.Attachment 1668781

Re: What did you do to your truck today part IV
 

I picked up my vent windows and a side window.I will test fit them and se how it goes.Attachment 1668924

Attachment 1668925

Re: What did you do to your truck today part IV
 

I patched up the extra holes in my high and installed it. Used rivnuts to so it can be removed as needed.

Re: What did you do to your truck today part IV
 

I replace my wiper blaids with a set of 12" Champion blades. I hade to buy a hole assembly and take it apart to use only the rubber. I hade to do a little cutting to make them slide in but they look like they will work well.

I also used a d-ring to lock my column shirt linkage in park (as a society measure). With the hood locked you can't take the truck out of park. I am also trying to figure out a way to lock my steering column inside the engine compartment.
Posted via Mobile Device

Re: What did you do to your truck today part IV
 

I was told to drill a hole in the shaft than put a bar in it.When you turn it it will hit the inter fender.

Re: What did you do to your truck today part IV
 

I put the wood in my bed.Attachment 1671047

Attachment 1671048

Re: What did you do to your truck today part IV
 

Attachment 1671050

Attachment 1671049

Re: What did you do to your truck today part IV
 

Fortunately I have a steering knuckle on my column so I don't have to drill a hole.

Re: What did you do to your truck today part IV
 

Ha! I think rvrfoot and I are on the same schedule.

I just got my wood installed this week/weekend myself.

Re: What did you do to your truck today part IV
 

I got a new back window had it tinted.Installed it and new seal.Attachment 1671291

Attachment 1671290

Attachment 1671289