Re: Project 69SWB
Quote:
Quote:
Posted via Mobile Device |
Re: Project 69SWB
Quote:
To lay the cab on its back, I enlisted my neighbor and a friend of mine. Myself and my friend each got on a rocker, lifted it up and tilted it to my neighbor and laid it down nice and easy. :smoke: I did not want to chance denting up the back after all the work. An no identity stolen... After many emails back and forth with the admins they fixed me up. Posted via Mobile Device |
Re: Project 69SWB
Quote:
|
Re: Project 69SWB
1 Attachment(s)
Took 1/2 quart of the UV protectant.
Operation Undercoat complete. :sumo: Posted via Mobile Device |
Re: Project 69SWB
1 Attachment(s)
This is last of the rust repair on the cab. Should get this taken care of this week.
Passenger side of cab roof. Rest of roof is just fine. Posted via Mobile Device |
Re: Project 69SWB
1 Attachment(s)
I plan to cut a piece from my other cab to fix both of these areas.
Posted via Mobile Device |
Re: Project 69SWB
Jimmy everything looks great. Your floor looks so good, I'm going to do my floor just how you did yours. Go easy on the roof repair, it will warp if your not super careful.
|
Re: Project 69SWB
subscribed! Nice job on the cab floor! that is on my to-do list very soon!
|
Re: Project 69SWB
Great job on the rust repair, I appreciate that you do things right.
One of the things I enjoy about this board is that I get to see alot of rust repair done right, guys are removing rust replacing with new metal then welding it in, then using the correct methods to fix dents, reshaping the metal instead of just filling with bondo, we live in a world where people don't take any pride in their work anymore but when I see all the honest, hard work people do here I have hope. |
Re: Project 69SWB
Quote:
Quote:
Quote:
|
Re: Project 69SWB
Floor looks terrific! Have fun with that roof.
|
Re: Project 69SWB
Quote:
|
Re: Project 69SWB
5 Attachment(s)
I cut out the bad section of the roof. You can see where I had originally drawn my line, but after cutting out the donor section.. I decided it's best to cut as little as possible.
Attachment 1071571 There had been some previous work done here. Instead of cutting out the bad section they just filled it in; It was also dented in here a tad so I wanted to get the dent out and did not want to fill it in with bondo. Attachment 1071572 I had to grind down the welds so I can fit this piece flat against my donor piece and get a nice line for cutting. Attachment 1071573 Here it is marked up and ready to cut. I left the donor piece on as a guide while I cut. Attachment 1071579 I sprayed some Eastwoods Fast Etch and Prep into the open section of the roof to convert the rust and it leaves a nice zinc phosphate coating.. I will still spray some primer in there before I seal it up. All in all the inside looked pretty good. Was just this corner that had a little pitting. Attachment 1071580 |
Re: Project 69SWB
1 Attachment(s)
Here it is just kind of laid in there... Still have a little trimming to do. This part of the rust repair went pretty smooth... I decided to stop last night it was getting late and I didn't want to rush through the welding part.
|
Re: Project 69SWB
Nice work on the cab
|
Re: Project 69SWB
Cool Build! Nice job on the rust repair. I was lucky in that department, and didn't have much to deal with. keep up the good work!
|
Re: Project 69SWB
Quote:
Quote:
|
Re: Project 69SWB
Looks good.
Posted via Mobile Device |
Re: Project 69SWB
Quote:
|
Re: Project 69SWB
Fitup looks good! A tip- open a beer. Turn good tunes on. Aim gun at one end. Tack. Sip. Aim at middle. Tack. Sip. Aim at end. Tack. Sip. Continue until done. Seriously, on the roof, go REALLY slow. You'll be fine, just don't throw a lot of heat at it in a hurry. Props on even attempting the repair. If you haven't welded it yet, consider tying a coathanger around a sock, dipping it in POR or the sauce of your choice, and rodding it down the inside of the seam, to kinda seal it up as best you can. Best of luck, it'll be cool. If the advice bugs you, don't be afraid to tell me to pound sand. Are you going to Brad's?
|
Re: Project 69SWB
Quote:
|
Re: Project 69SWB
Roof repair looks good Jimmy, I'll stop holding my breath now. Glad you didnt have any problems with it.
|
Re: Project 69SWB
1 Attachment(s)
Thanks Scott. It went pretty good, I wouldn't say perfect. It pulled on me in a couple places. Ill just have to fix it in the next stage.
Posted via Mobile Device |
Re: Project 69SWB
1 Attachment(s)
And after grinding down the welds.
Posted via Mobile Device |
Re: Project 69SWB
1 Attachment(s)
Can only upload 1 pic at a time from my phone.
Here's another. Posted via Mobile Device |
All times are GMT -4. The time now is 03:00 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com