got exaust fabed and hung today
 

made stainless flanges 2 1/2 " stainless pipe 40 series stainless flowmasters all tigged welded together still need to make up tail pipes first pic

2

You are an exhaust building inspiration.

Mandrel bends......ooohhh that's like car porn to me.

3

actually all fittings are to be finished 45's with tapered cuts to get desired direction mandrel bender only goes up to 2 1/8"

4

5

How bout some pics of that 4 link setup:D :metal:

wow dude, that looks awesome.:metal:

Nice work Valley. that's how I'm planning to do mine also

Very nice... I need pipes on my truck. Come on over.

Nice looking setup, how low does it hang though? Also, I'd like to see more pictures of your truck, especially the rear suspension.

Looks Great Dude! Like to see more pics of not only the rear suspension but entire truck!

You should get those mufflers powdercoated. That looks awesome!

wow! love your truck! what kinda mufflers? flowmasters? that exhaust looks great!

That truck is killer and damn near the same color mine will be I can not wait untill sunday to get to work on it..

That is some good looking pics you got there, send us more so I can drool some more:D

very nice........clean and sanitary look...

Hey pr here a few pic's of valley's truck that I have hope you don;'t mind me postin them valley..

Small block..

I see you are just letting the mufflers end with no tailpipes...

Good work...Flow's sound the best that way :D
Especially if you have a mean motor, what it looks like you do :burnout:

Your truck's a real piece of work, awsome! :cool:

I have to say that truck is a work of art, very, very nice. Do you have a chrome fly wheel dust cover to put on there?

thanks guys for the comments. i will be running tail pipes just have to get bed mounted to see where to go with them they hang about 1 1/2" below frame rail truck is bagged but im not laying frame just want truck to sit low and still be able to clear speed bumps when needed trucks front tire has about 1/8" clearence before it hits and had to bring up rear 1" up so i would not have to do cut through again i just want low but dont want tofab up new inner fender wells for frnt and hood hinges as well as making larger c-notch im happy with what i have i wim post pics of 4 link later my daughters calling

Is that with the stock tranny crossmember?

Jay

What type of headers do you have on that motor?

cross member is one I made for 700r4 trans headers are sanderson C-10 . The haeders on motor pics were hugger headers that were just going to make more bends than I wanted so I swapped for the sandersons imo great quality headers they are also ceramic coated. still need to clean up mufflers to match tubing and get rid of weld spots. and make them look more presentable. as for 4 link pics here you go and no i dont mind when some else post pics other than me its kind of cool that you guys keep track of it and all of the comments are much appreciated we just do what we can. we just do it on the side to have fun and do work for friend and aquaintences. we have 2,41 willys were waiting for parts for to continue here are pics of it 2nd willys the same only will be stuffing 392 blown hemi.

4 bar

4 link

front brackets are same elevation as bottom of frame stainless bars as is panard bar that we put a break in bar to keep rear from kicking over from full up to full down rear shifts 3/16th" from ride height set up rear axel mounts are welded to axle tube then we welded air ride brackets to them.

heres the willys

w

w1

w2

427 tall deck 400 trans fab 9 inch ifs rack and pinion 4 wheel disk brakes

Your truck is Sweeeeeeeeet!! So is that Willys! WHere abouts in central Cali are you?? Stockton here. 70short/step

What color is that on the Willys? Looks great.

Jay

its just the gel coat

That exhaust is very impressive!!

Oh man I like that 4-link...Where'd you get the parts or did you fab it up yourself? was your truck a coil or leafspring truck? I'd love to do something like that in the future. Damn nice rides you got there dude.