|
"My wife now hates me" build. 383 stroked and bagged
I bought this truck in April for 2k. It has a 383 stroker (or strong 350) and 350 trans with shift kit. 3.08 in the rear but I have liberty 3.73 gears with eaton posi boxed up brand new in my sons room. It's bagged all way with 8 valves, 2 compressors, and 2 5 gallon tanks. The A-frames have been replace and are tubular and the front is not disc brakes. When I bought it the guy who sold it was a moron. It was running off of 5 cylinders due to the headers burning the spark plug wires. Header plugs fixed that. After a tune up man did she come alive! Anyone the guy didn't do the work, he bought it from someone who did and he just didn't know how to do anything. I believe he did manage to slam the truck while it was in motion and bent the front x-member and scrapped up the lower a-frames. We will get to that later.
http://i408.photobucket.com/albums/p...k/101_0012.jpg http://i408.photobucket.com/albums/p...k/101_0011.jpg http://i408.photobucket.com/albums/p...k/101_0010.jpg http://i408.photobucket.com/albums/p...k/101_0013.jpg The interior, in the picture I have some things taken apart, parts and stuff all over the seat. http://i408.photobucket.com/albums/p...k/101_0048.jpg Part of the wiring nightmare I temporarily fixed. Replaced those relays and I'm going to reroute the wiring to go between the tanks. Also my rear bumper bracket that look like they have been cut? http://i408.photobucket.com/albums/p...k/101_0045.jpg A-frames http://i408.photobucket.com/albums/p...k/101_0052.jpg The few rusted areas, oh year, the rockers have been replaced as well. http://i408.photobucket.com/albums/p...k/101_0055.jpg http://i408.photobucket.com/albums/p...k/101_0056.jpg http://i408.photobucket.com/albums/p...k/101_0057.jpg This is the passenger side A-frames and x-member. Notice how the x-member is buckled by those 2 bolts holding the lower A-frame on? Idiot PO. http://i408.photobucket.com/albums/p...k/DSC02019.jpg |
Re: "My wife now hates me" build. 383 stroked and bagged
http://i408.photobucket.com/albums/p...k/DSC02020.jpg
This is the right side, how the x-member is supposed to be. Notice no buckle? So I decided that x-member had to go. Got a used one in good condition from a guy and started taking stuff apart. Here is my hoopty ass setup, lol. http://i408.photobucket.com/albums/p...k/DSC02145.jpg\ Started off by removing the power steering pump, notice how it's not completely straight? Will have to work on that during re-install. http://i408.photobucket.com/albums/p...k/101_0044.jpg http://i408.photobucket.com/albums/p...k/DSC02115.jpg This is the 2x4 helping the motor mounts hold the motor when I remove the x-member. http://i408.photobucket.com/albums/p...k/DSC02120.jpg I then removed all of the steering components and unhooked the brake lines, I'm going to need to replace the front lines later on... http://i408.photobucket.com/albums/p...k/DSC02133.jpg http://i408.photobucket.com/albums/p...k/DSC02128.jpg I'll post more tomorrow, got plenty more to go... |
Re: "My wife now hates me" build. 383 stroked and bagged
So I took all the bolts off of the x-member and dropped it.
http://i408.photobucket.com/albums/p...k/DSC02156.jpg This is the motor mount that is no longer being supported by the x-member thanks to my trusty ol' 2x4. http://i408.photobucket.com/albums/p...k/DSC02123.jpg So here it is, finally got the x-member out after 3 days and plenty of busted knuckles and an extreme amount of frustration. http://i408.photobucket.com/albums/p...k/DSC02158.jpg http://i408.photobucket.com/albums/p...DSC02163-1.jpg Here is is painted and all bolted in. http://i408.photobucket.com/albums/p...k/DSC02353.jpg http://i408.photobucket.com/albums/p...k/DSC02354.jpg |
Re: "My wife now hates me" build. 383 stroked and bagged
Whewwww, now all that's left is to bolt the motor mounts up, should be a breeze right? WRONG!!! I have 2 different sets and they will not line up to the x-member holes. Wow this turned out to be way more then I expected.
http://i408.photobucket.com/albums/p...DSC02357-1.jpg http://i408.photobucket.com/albums/p...k/DSC02356.jpg These are the mounts, 2 are the same and the 1 that's different is the one that I left connected to the motor. The other is still connected but none will line up, looks like I will be drilling into my newly painted and bolted x-member! http://i408.photobucket.com/albums/p...k/DSC02358.jpg http://i408.photobucket.com/albums/p...k/DSC02359.jpg Ok, now that catches me up to where I am right now. I will continue to post progress most likely tomorrow when I drill the motor mounts into the x-member. |
Re: "My wife now hates me" build. 383 stroked and bagged
Drilled the X-member and bolted on the motor. Also bought a 350 out of a 79 vette for $50. That will be my slow 400+ hp slow build. Drilled the holes for my bag brackets and for the hoses, pictures to soon follow....
|
Re: "My wife now hates me" build. 383 stroked and bagged
nice build
|
Re: "My wife now hates me" build. 383 stroked and bagged
Nice build how is the back bagged
|
Re: "My wife now hates me" build. 383 stroked and bagged
Back is also bagged, the wiring in the back is a nightmare which I put a bandaid on. Still working on the front then will work my way back. Finally got my brackets and bags mounted onto the a-frames, still need to shim the a-frames, will get to that tomorrow after I get some.
http://i408.photobucket.com/albums/p...k/DSC02366.jpg http://i408.photobucket.com/albums/p...k/DSC02370.jpg http://i408.photobucket.com/albums/p...k/DSC02372.jpg http://i408.photobucket.com/albums/p...k/DSC02379.jpg http://i408.photobucket.com/albums/p...k/DSC02380.jpg |
Re: "My wife now hates me" build. 383 stroked and bagged
I really really really need to tackle this, but I still need a wiring diagram to follow and the ones I have found are not very clear.
http://i408.photobucket.com/albums/p...k/DSC02381.jpg One of many results of said wiring...Truck is off btw... http://i408.photobucket.com/albums/p...k/DSC02382.jpg |
Re: "My wife now hates me" build. 383 stroked and bagged
followng along
|
Re: "My wife now hates me" build. 383 stroked and bagged
Nice! i wish i could help with that wiring haha
|
Re: "My wife now hates me" build. 383 stroked and bagged
Me too! I have nightmares about it when I fall asleep at night. Notice how the starter switch wiring is spliced into all red wires? Yeah, awesome.
|
Re: "My wife now hates me" build. 383 stroked and bagged
what year chevy is that seat from?
|
Re: "My wife now hates me" build. 383 stroked and bagged
Quote:
|
Re: "My wife now hates me" build. 383 stroked and bagged
Ok, got out there the last 3 days and maybe screwed in 6 bolts. It's been like 100 out with crazy humidity. So I got my lower control arms torqued to 65ftps and bought some fuel lines and a line bender.
http://i408.photobucket.com/albums/p...k/DSC02385.jpg Isn't this bend so purty??? http://i408.photobucket.com/albums/p...k/DSC02386.jpg That pipe bender is from harbor freight, it was $6 and it works great. Here is the passenger side, it was the reason why I had to replace the x-member due to it being buckled. Well as you can see it kind of deformed the bag a little bit, hoping when I put some air to it, it will take it's original shape and when I drop it, not get caught in anything. http://i408.photobucket.com/albums/p...k/DSC02388.jpg here is the right drivers side, I just need to put the rotor back on and connect the steering blah blah blah. http://i408.photobucket.com/albums/p...k/DSC02389.jpg It is a real pain in the ass to get these lines bent with everything put together. I struggled today and got sick of being blazing hot so I called it a day. Also, I need to replace my trans gasket due to me installing B&M shifter and loosing 2 of the bolts. Not sure if you can see, but there are only 2 bolts holding the trans x-member, one of the bolts is rounded off inside of it. I will have to cut that one off. http://i408.photobucket.com/albums/p...k/DSC02390.jpg Found a better use for the top to my sons sand box. It's better then using it to cover up one big ass kitty litter box that was supposed to be a sand box for my son. Damn stray cats! http://i408.photobucket.com/albums/p...k/DSC02391.jpg |
Re: "My wife now hates me" build. 383 stroked and bagged
Also bought a 350 out of a 79 vette for $50. It sat outside for like 2 years but I cleaned it up a little bit. Still need to take it to the machine shop to make sure no cracks and get it machined. It's a 2 bolt but I'm still going to try to get it to about 400hp. That will take me years to complete though. Not in any type of hurry.
http://i408.photobucket.com/albums/p...k/DSC02394.jpg Crank and pistons, a lot of rust too... http://i408.photobucket.com/albums/p...k/DSC02393.jpg |
Re: "My wife now hates me" build. 383 stroked and bagged
Also, can someone give me some advice. I'm sure I need to rebuild my carburator, but my truck never smoked. I installed the gas pedal bracket that holds the linkage on. It was being held on with a nail. I then adjusted the idle and fiddled with the 2 screws in front. I closed the left and turned it 3 turns, then did the same to the right to make it match, well now it smokes. I'm not a mechanic, I'm learning as I go but is there a way I possibly could of blown a ring or something when I adjusted the carb? It's in pretty bad shape I think. When I got it, it had a cheap air filter and the housing had a huge hole in the front for a hose or something. Well it was not being plugged so that was all unfiltered air going in for god knows how long. It was also all dingy, and I left it without the filter on for like a month, didn't run it during that time but I think that may have the float sticking. Any advice would be very appreciated. Thanks for following guys, you all keep me motivated through all the *****ing my old lady does.
|
Re: "My wife now hates me" build. 383 stroked and bagged
I have messed with the mixture screws to but it seems like they don't do anything anymore? I can close them and I get nothing, before it would stumble and almost die. I'm just worried about the smoke!
|
Re: "My wife now hates me" build. 383 stroked and bagged
Some updates for those who have been following me, I removed, clean and painted the trans pan and the tie rod steering bar? I also finally got my brake lines done and installed the upper ball joint. http://i408.photobucket.com/albums/p...k/DSC02395.jpghttp://i408.photobucket.com/albums/p...k/DSC02396.jpghttp://i408.photobucket.com/albums/p...k/DSC02397.jpg Now what I had to do to get the brakes lines done. It was a fiasco trying to figure out which advanced auto part would fit. I know I have a 67 but I have disc brakes, now I ordered the ball joint (OE brand) for a 71 but it would not fit and it was metric. The picture it had on advanced computer showed a picture of what I pulled off the truck but the one they gave me looked complelty different. Apparently they had in the system that a 67-71 had the same exact ball joint. Well after a bunch of crap I ordered a 71 Moog ball joint and it fit thank god. Then I tried to order some brake hoses. Well yet again, advanced had the wrong stuff in the computer I guess because they could not show me one that would fit. I went to O'reillys and they hooked me up. All i have to do now is replace the inner and outer tie rods and then she can finally move again!! YAYYYYYYYYYYYYYYYYYY! Oh yeah, I sprayed my carb with some carb cleaner and it fixed it, now running like it should I think. We will see when I get it on the road.
|
Re: "My wife now hates me" build. 383 stroked and bagged
oh yea, I still need to secure the brake line, I have the clips and self tapping screws that I will try to get done tomorrow.
|
Re: "My wife now hates me" build. 383 stroked and bagged
SOB!!! Well, I got everything put back together and bled the brakes but could not get all the air completely out, think it's my MC so I bought a new one and bench bled it, just need to put it on. Well I drove it down the street a bit just to actually drive it, it's been like 3 months. Drove great! My order from CPP came in, I got front and back shock relocators and shocks. Just found out I think I have the wrong shocks. No big deal, I just need to make sure of the size I need and they will except a swap. Well I go to start it up and it's running very rough, almost like a cylinder is not firing. So I pull the #1 plug and I can't tell a difference in the motor, I put it back in and pull the #2 plug, can't tell a difference and both shocked the living piss out of at the distributor. Tomorrow I'm going to pull the plugs and see if one is gunked up which is very likely with the way my carb has been running. Man I tell you, this truck is just one thing after another. Don't get me wrong, I still love it but it seems sometimes to just be too much for me! Fix one thing, 2 more things go wrong, fix those, then it's something else! My wife is sure enjoying talking trash "I told you you shouldn't of bought that stupid truck" or the classic " Maybe if you had'nt bought that truck then you would be able to relax" blah blah blah blah, that's what I hear anymore. Sorry, just venting...stupid truck!
|
Re: "My wife now hates me" build. 383 stroked and bagged
Sorry to hear about the trouble....hope it does turn out to be an easy fix.
|
Re: "My wife now hates me" build. 383 stroked and bagged
Me too man, me too. Where is Midlothian? I'm from Hampton roads.
|
Re: "My wife now hates me" build. 383 stroked and bagged
Quote:
|
Re: "My wife now hates me" build. 383 stroked and bagged
Oh ok, well hello from a fellow Virginian? What ever we are called, I moved to Alabama and I miss VA so much. Nice to know some people back home have very good taste though!
|
Re: "My wife now hates me" build. 383 stroked and bagged
Still troubleshooting my damn distributor, here is a link if anyone can possibly help...
http://67-72chevytrucks.com/vboard/s...=417213&page=2 |
Re: "My wife now hates me" build. 383 stroked and bagged
Ok here is a update. Since my last post I have done a few things. I have rebuilt my edeblock 1405 carb, welded my front shocks mounts onto frame and installed. Also took bed off and bolted on my upper shock mounts but could not break the axle u bolts to replace that bracket so I used orginal. I used a 3/4 ratchet with 1-1/16 socket with a 3 ft conduit and still could not break it loose kicking on it. Now that the bed's off I am thinkng about just sanding the frame and repainting it. Pictures soon to follow.
Posted via Mobile Device |
Re: "My wife now hates me" build. 383 stroked and bagged
I fixed my dist problem also, it ended up being some fouled plugs. Now I need to redo a few air fittings and they are seized in the tank. I guess a torch is the only way to get them out? I stripped the fittings trying to pull them off.
Posted via Mobile Device |
Re: "My wife now hates me" build. 383 stroked and bagged
Love the truck charx2. I feel your pain on the u-bolts. To get mine off, I took my 1/2 ratched (don't own a 3/4) and my floor jack handle. I put the wheels on and the truck on the ground and pulled as hard as I could while pushing against the wheels with my feet. It was a PITA, but they finally broke loose. Good luck on the build!
|
Re: "My wife now hates me" build. 383 stroked and bagged
Thanks tubbed, I tried something similiar, I used the 3/4 (which is my neighbors) and had a huge breaker pole(lol) on it and used my feet against the frame to give me leverage. I think the pole was too big because when I would get some real power going or start to try and kinda rock it, the pole would slip out. I might try it like your saying with my 1/2 and a new smaller breaker bar I just picked up today from the worksite. Man I need to update this build...
|
Re: "My wife now hates me" build. 383 stroked and bagged
Ordered a step notch and a panhard bar, it's been 11 days and they have still yet to ship. I also ordered a Millermatic 211!!! That will be in today and I am super stoked about finally getting a good machine! As the weather gets nicer and I get free time, I will be working on ol Betsy. I go to school full time and work full time and in between I pretty much hang with the family, so time is scarce. I hope to have it back on the road and hitting switches by the end of the summer. Progress will resume shortly.
|
Re: "My wife now hates me" build. 383 stroked and bagged
Thats sweet!!!
|
Re: "My wife now hates me" build. 383 stroked and bagged
keep up the good work...looking good
|
Re: "My wife now hates me" build. 383 stroked and bagged
Ok so some updates here. I made myself some 2" drop blocks out of square tubing. I didn't like the open sides so I welded some plates I cut out and grinded them down. Turned out pretty good if I don't say so myself...
http://i408.photobucket.com/albums/p...k/P5162970.jpg To take the U-bolts off this is what I had to use. A 5ft breaker tube... and it was still tough! http://i408.photobucket.com/albums/p...k/P4162868.jpg Even with that I still ended up breaking a Craftsman 1/2" ratchet. Took it back and got a 18" breaker bar that I stuck inside that 5ft breaker tube http://i408.photobucket.com/albums/p...k/P4162870.jpg |
Re: "My wife now hates me" build. 383 stroked and bagged
Oh, here's my new machine that made all this work possible, and also helped me learn to weld! Here also is a picture of me heaving on that breaker bar I had to use to break those U-bolts free!
http://i408.photobucket.com/albums/p...k/P4072786.jpg http://i408.photobucket.com/albums/p...k/P4302925.jpg So after the drop blocks, I put together the step notch I got from suicidedoors. I tacked most of it together and then tried to fit it. I then realized that it would not fit like I had hoped so some cutting out and trimming of parts was needed. http://i408.photobucket.com/albums/p...k/P3212478.jpg I cut out the cross member that holds on the upper shock mounts. I then welded a piece of square tubing across the frame to hold it in place while I did my work. http://i408.photobucket.com/albums/p...k/P3262542.jpg My neighbor persuaded me into not cutting out that other cross member behind the axle, so I instead decided to notch out the notch. I made a card board template and notched it out on driver and pass side. I then used some square tubing to bridge the notches together. Here are the only good pictures I took. http://i408.photobucket.com/albums/p...k/P4302923.jpg http://i408.photobucket.com/albums/p...k/P4302928.jpg http://i408.photobucket.com/albums/p...k/P5152948.jpg http://i408.photobucket.com/albums/p...k/P5152949.jpg http://i408.photobucket.com/albums/p...k/P5152951.jpg |
Re: "My wife now hates me" build. 383 stroked and bagged
nice progress!
|
Re: "My wife now hates me" build. 383 stroked and bagged
Final pics of it just about finished. Still wet with paint! Don't mind that tab on the bigger of the bridge bars, I forgot to grind it off. Now I am regretting not cutting out that cross member behind the axle. Everything from the cab to the back of the step notch is square and level. Behind that stupid cross member ( which from the factory was put in crooked) the pass side sits about 1/2" higher(or lower) than the drivers side frame. No big deal really just means I will have to fab up some brackets for a bumper to make it level, but I should have just cut that thing out!
http://i408.photobucket.com/albums/p...k/P5162960.jpg http://i408.photobucket.com/albums/p...k/P5162961.jpg http://i408.photobucket.com/albums/p...k/P5162962.jpg http://i408.photobucket.com/albums/p...k/P5162963.jpg That's level http://i408.photobucket.com/albums/p...k/P5162964.jpg http://i408.photobucket.com/albums/p...k/P5162967.jpg http://i408.photobucket.com/albums/p...k/P5162968.jpg Not level! http://i408.photobucket.com/albums/p...k/P5162969.jpg The front sitting on 8" 4x4. http://i408.photobucket.com/albums/p...k/P5162966.jpg |
Re: "My wife now hates me" build. 383 stroked and bagged
Now I just need to figure out how I'm going to mount my bags. I'm thinking about just mounting them over the axle and just getting some new sleeved bags because I know the double convulated(spelling?) bags ride like trash above or behind the axle. Any suggestions would be greatly appreciated! I'm going to re-plumb alot of the stuff as well to install my new tank. The summer has started and so has the work! More to come....
|
Re: "My wife now hates me" build. 383 stroked and bagged
hey whats up man?
you make any progress on them rear bags? |
Re: "My wife now hates me" build. 383 stroked and bagged
Still working on fabbing up the rear mounts. Its pretty ruff not having the correct metal cutting tools. I am using conduit to get my templates then will trace to DOM tubing. Definetly will be custom though. Bout to start an addition on my house also so ill have to find the time. Ill post some progress pics whenever I get through with these templates. How about you man?
Posted via Mobile Device |
| All times are GMT -4. The time now is 05:47 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com