Re: SANFORD build thread
 

Thanks guys,lolife99 it is to the driver side,I did not center the r&p housing,the rack It has a 2 1/2 turn lock to lock,I centered it between left and right and tried to center the outer tie rod swivel which is under the boot,however I did manage to get it to the driver side about a 1/2 to far,I know It should be exactly centered but I am going to check the bumpsteer when I do the alignment,if things do not work out Speedway motors has a set of offset mounting bushings that I will use to move it.Time will tell but honestly for a cruiser I dont think I will notice any difference except maybe turning radius.Hope this makes sense.Thanks for looking guys.

Re: SANFORD build thread
 

Nice fab work, wheels and tires are killer. perfect stance.

Re: SANFORD build thread
 

bump

Re: SANFORD build thread
 

Nice build. Sanford is looking good!

Re: SANFORD build thread
 

update,I have just about everything finished in the rear,I was able to set my pinion angle and then I installed my lower bag mounts.I had to move the upper bag mounts in order to get the truck to sit where I wanted it to.I also braced everything up pretty good because I will be doing a little bit of towing with this thing,I got the shocks mounted as well.I am pretty much finished with the fabrication on the rear suspension just a little bit of final welding when I strip it down to paint it.I also re-purposed the factory bump stops so if it does bottom out it hopefully will not damage anything.Attachment 938447

Attachment 938448

Attachment 938449

Attachment 938450

Attachment 938451

Re: SANFORD build thread
 

I also have most everything for the exhaust,I got a spare set of headers on the cheap that I will cut up and use to modify the ones I will use.well that is it for now. Thanks for lookingAttachment 938461

Attachment 938462

Attachment 938463

Re: SANFORD build thread
 

one of my favorite builds going on, such nice work on the rear :metal:

Re: SANFORD build thread
 

subscribed

Re: SANFORD build thread
 

Just a small update,I have been working on some loose ends and one of those was getting the steering shaft made which in itself was not that hard however modifying the motor mount was a major PIA.I spent most of today doing that and re-enforcing the mounting tab on the trans mount.I also shortened my drive shaft so I will send it out to have balanced.I still have to make the upper shock mounts and then on to the exhaust.Attachment 942538

Attachment 942539

Attachment 942540

Attachment 942541

Attachment 942542

Re: SANFORD build thread
 

this is what the shaft looks like and the motor mount mods complete,in some of my previous posts it was pointed out that my rack wasnt centered in the frame,I knew it was to the drivers side a little but after checking it with the crossmember in the frame rail it was off more than I thought so I cut it out and re-positioned it,so this was a screw up on my part but now is the time to fix it.That is how it goes sometimes and thanks for pointing that out.Thanks guys for looking. Attachment 942544

Attachment 942545

Re: SANFORD build thread
 

not a lot to update,but I did finish modifying the headers and making the exhaust,I forgot to take a pic before I removed it from the truckAttachment 959857

Attachment 959858

Attachment 959859

Attachment 959860

Attachment 959861

Re: SANFORD build thread
 

Attachment 959862

Attachment 959863

Re: SANFORD build thread
 

such nice work,killer job

Re: SANFORD build thread
 

Dang i havent checked up on this in a while!!! Killer fab work man!!! Keep it up its looking great
Posted via Mobile Device

Re: SANFORD build thread
 

Just a small update.I am just about done with all the heavy fabrication,I still have a few things like front shock mounts,front sway bar ,trans linkage and so on.I still have to finish modifying the trailing arm crossmember and get the rear brake assemblies on and route the parking cables.I will blow this thing in the near future and paint the chassis and other components etc.thanks for looking.Thought I would trow a few pics of it together one last time before paint.Attachment 970842

Attachment 970843

Attachment 970844

Attachment 970845

Attachment 970846

Re: SANFORD build thread
 

few moreAttachment 970862

Attachment 970863

Re: SANFORD build thread
 

Nice work! So...no issues with clearance with the exhaust at the notches?

Re: SANFORD build thread
 

Hol-y man. This is coming out super awesome. Looking forward to some paint shots. Inspiring build thread!:metal:

Re: SANFORD build thread
 

always such nice work!

Re: SANFORD build thread
 

looks well laid out and tidy.nice job.

Re: SANFORD build thread
 

Thanks guys,VA72C10 it does appear it is hitting,but it is not.also this is at full drop and there is at the closest point about 3/8 clearance so I dont think there will be any problems.I have had this thing together and apart about 3 or 4 times to check for any unforseen problems.Hopefully this is the last time as I am about to lose a little steam on this project.Wife and I have made reservations for power tour next June so I better get on the ball.Thaks again.

Re: SANFORD build thread
 

Dig your work !

Re: SANFORD build thread
 

got the engine ready to go in,currently cleaning and painting trans and other driveline components,will update Attachment 979857

Attachment 979858

Re: SANFORD build thread
 

nice & clean

Re: SANFORD build thread
 

Damn..that motor color looks like a Jolly Rancher candy..makes you wanna lick it..wow did I say that!..:lol::lol::lol: nice job:metal: