Parting out 69 C20 PRICES LOWERED!!!
 

Got what's left of a '69 C20 to part out. Cab and bed sheet metal was junk, so that's gone to scrap metal. Here's what I have off so far:

Headlight trim, straight light surface rust sold

Fender emblems, some over spray, easily cleanable SOLD

Front turn signals with lenses sold

Gauge cluster, nice printed circuit, everything works SOLD

4 row radiator clamps, rubber good. sold

Headlight buckets with springs and adjusters sold

Tailgate trunions 10.00 shipped

Ball bearing ashtray, crappy paint job, but works great! 10.00 shipped

Lighter, headlight switch, and wiper switch with knobs, headlight switch looks
fairly new. tiny bit of over spray on lighter trim that will clean right off. All
in working condition SOLD

Hood latch with support. Nice and straight, works fine 25.00 shipped

Brake booster w/ proportioning valve and master cylinder. For drum brakes,
works fine. SOLD

High hump trans tunnel. Very nice!!! With bolts SOLD

Saddle seat belts, needs cleaning, pitting on chrome on 1. 1 buckle has
a little cracking SOLD

Saddle visors, very nice SOLD

Aqua blue/ green visors, very nice SOLD

Chrome 1 wire alternator, working condition, don't know the
amperage. dsSOLD

4 row radiator. Aftermarket, appears to be recently replaced. Fins are
perfect. Very nice. SOLD

Left fender, very clean, no dents, cup is good. PO screwed front molding in with 2 small screws, otherwise really nice shape SOLD

Right fender, same screw holes, but 4 instead of 2. Cup has rust, but the rest
is very nice. SOLD

I'll be adding more as I get it apart. If you don't see it, ask, I might have it!!


https://lh4.googleusercontent.com/-R...8/IMG_4404.JPG

https://lh6.googleusercontent.com/-O...8/IMG_4405.JPG

https://lh4.googleusercontent.com/-Z...8/IMG_4406.JPG

https://lh5.googleusercontent.com/-o...8/IMG_4407.JPG

https://lh3.googleusercontent.com/-u...9/IMG_4413.JPG

https://lh5.googleusercontent.com/-U...9/IMG_4414.JPG

Re: Parting out 69 C20
 

I will take the emblems if the studs are intact.
Engine stands?

Re: Parting out 69 C20
 

They are intact, with the nuts on them as well. I have 2 sets of small block engine stands. No big block, as this truck was converted at some point.
pm sent on the emblems.
thanks, Scott

Re: Parting out 69 C20
 

i'll take brake booster

Re: Parting out 69 C20
 

I need the part of the floor where the high hump cover bolt to if you still have the cab ?

Re: Parting out 69 C20
 

Interested in the lighter and switch set. Do you have the wiring harness for the lighter? Is the headlight switch a gm part?
Posted via Mobile Device

Re: Parting out 69 C20
 

Pm sent.

Re: Parting out 69 C20
 

I do have the harness, I'll throw that in. Switch looks aftermarket, but that's not a bad thing. Put 2 Delco switches in my truck, 1 took a dump after 2 months, and the replacement was DOA right out of the box!

Re: Parting out 69 C20
 

No sorry. I cut it up because it was badly rusted. I'll keep an eye out though.

Re: Parting out 69 C20
 

I'll take the seat belts. PM me your payment info.

Re: Parting out 69 C20
 

pm sent

Re: Parting out 69 C20
 

Hey scottg I was mostly concerned with the knobs looking the same including the brushed metal inserts. Do they? Would all the parts clean up real nice? Does the lighter assembly have a light? Just curious. Thanks
Posted via Mobile Device

Re: Parting out 69 C20
 

All knobs are identical, they will clean up nicely. Lighter does not have a light.

Re: Parting out 69 C20
 

payment sent<<<

Re: Parting out 69 C20
 

Thanks Paul.
Scott

Re: Parting out 69 C20
 

I'm looking for a bellhousing #3925505

Re: Parting out 69 C20
 

I will take the cluster. PM me with payment info

Re: Parting out 69 C20
 

Do you still have the big block power steering hose

Re: Parting out 69 C20
 

I have one, but not sure of the #. I'll check when I get home.

Re: Parting out 69 C20
 

PM sent. Thanks, Scott.

Re: Parting out 69 C20
 

You know, I might. The p/s bracket doesn't look right to me for a small block, so the PO might have used the original on it. I'll get back to you on this.

Re: Parting out 69 C20
 

Paypal sent. Thanks

Re: Parting out 69 C20
 

Hey Scott, I'll take the lighter w/harness and switches. PM me with payment info. Thanks

Re: Parting out 69 C20
 

Thanks Scott, I need the 5 inch opening, not the 4.xx inch opening.
Posted via Mobile Device

Re: Parting out 69 C20
 

PM sent, thanks!