Re: 90 burb (( daily dragger))
 

I'm not trying hard to sell it so it may get some work done when it warms up

Re: 90 burb (( daily dragger))
 

I got my taxes done and should have a check end of month so not selling it
look for progress early feb

:metal:

:metal:

Re: 90 burb (( daily dragger))
 

YES! So happy you are not getting rid of it.

Re: 90 burb (( daily dragger))
 

me to I will get 4runner end of month to play with while I pull the burb apart
to add a cross member an then raise tank has to be back together for a show mid march for my kids high school fundraiser

Re: 90 burb (( daily dragger))
 

I second this statement. Now im anxious to see progress updates :metal:

Re: 90 burb (( daily dragger))
 

it was 20 degrees with 15-20 mph winds and got 4 inch of snow today
I'll wait till feb to look at it again

Re: 90 burb (( daily dragger))
 

that sucks bro...too damn cold

Re: 90 burb (( daily dragger))
 

55 degrees friday may get the fuel tank out and cut off the back of leaf springs to measure out my 2 link setup
pinch welds prepare to meet pavement :metal:

Re: 90 burb (( daily dragger))
 

cut dat chit up bro...LOL

Re: 90 burb (( daily dragger))
 

my side project was building the bath and closet for my master bedroom hoping to stuff the burb in the garage later this week and spend some quality time with it :lol:
going to mock up my rear links bags mounts and remove everything to prep for a 2" dropped cross member

Re: 90 burb (( daily dragger))
 

Yea!

Re: 90 burb (( daily dragger))
 

closet done hanging shelf system tomorrow
ruff in plumbing for bath this weekend
some times I hate being handy takes away from my truck time :lol:

side note got a 12 gal tank mounted valves on it
picking up air line tomorrow
thinking flat black with red stock rims and white wall tires
what do you'll think about that? old school ride

Re: 90 burb (( daily dragger))
 

i know what ya mean i am the same way...I think that sounds cool... i dont know about the white walls though, would have to see it first.

Re: 90 burb (( daily dragger))
 

well after installing new upper balljoints, break rotors,fuel pressure regulator and a set of new 31" bfg all terrian on the wife's 98 explorer the motor just crapped out :waah:

so quick tank and bag install bolt exhaust on and start driving burb till I get her a chevy this time she wants a late 90's tahoe :metal:

Re: 90 burb (( daily dragger))
 

well I cleaned out the burb this week and got the radio installed
I haven't clean or vacuumed it out since last may when the inspection died
well exhaust is on adding shock sunday hoping to tag and inspect it on wends
then have a shake down run next weekend

Re: 90 burb (( daily dragger))
 

:metal::bann::c2:

Re: 90 burb (( daily dragger))
 

http://i37.photobucket.com/albums/e9...ew021110-2.jpg

hoping to have this home friday for the family ride

little insight 88 half ton buckets up front
hitch w/ controller good driver quality :lol:

Re: 90 burb (( daily dragger))
 

nice bro...

Re: 90 burb (( daily dragger))
 

that then had more rot than most stuff from NY badly rusted with a nice paint covering both rocker, all 6 drs, fenders,quarters,rear wheel well had a 1.5" gap from rust you could see in carpet
sad though interior was perfect :waah:
owell back to my burb :lol:

Re: 90 burb (( daily dragger))
 

oh well

Re: 90 burb (( daily dragger))
 

any updates? wife's ride, or yours?

Re: 90 burb (( daily dragger))
 

nothing lately pasted on buying the burb rusted bad all round
hoping to rework rear end measure for tank/cell replacement
having to move parking brake bracket and what ever will keep it laying on frame

Re: 90 burb (( daily dragger))
 

building my 2 link kit right now will lay frame in rear.
now debating on the front thinking 2" z and 2" sectioned crossmember
I need about4-5" to lay on pinch welds. frame is about 2" below body
what to do next??

Re: 90 burb (( daily dragger))
 

body drop....

Re: 90 burb (( daily dragger))
 

no need for a body drop if I redo the frame with 2x4 stock I can cut off the pinch welds and lay body
major set back I ripped out all the tub and notch work to start over
guy f'd it up tubs are set back 4 inches from center,bridge cover was 6"
above frame notch,tubs are 8" wider than needed
debating a 3 link with a wish bone now then build back around it
want to reuse my 3rd row seat so we can all cruise around in it?