|
Re: Owen's C10
Quote:
|
Re: Owen's C10
1 Attachment(s)
me and buddy went and picked up the doors tonight....$200 I didn't think it was too bad a deal...
|
Re: Owen's C10
4 Attachment(s)
I'm so sick of grinding rivets!....10,000 later and the rear end and all the other crap is gone..
|
Re: Owen's C10
5 Attachment(s)
I had to go and take the 10 bolt out of the Camaro, cut all the brackets off, then find the gears, bearing races and shims, and get them and the axles back in. I cut the mounts off the eaton rear end so I could mock up the Camaro 10 bolt and tack it in place. I want to run porterbuilt tubular drop arms later down the road....just jammed the wheels on it for now.
|
Re: Owen's C10
5 Attachment(s)
....started cutting the drip rails off, not fun, but well worth the effort!
|
Re: Owen's C10
3 Attachment(s)
...just need to finish the drivers side then it's done.
|
Re: Owen's C10
I ordered some new rotor's and bearings today, so this weekend it will be a rolling chassis....it would be awesome if that step notch showed up by Friday!
|
Re: Owen's C10
3 Attachment(s)
...new rotors on, wheels bolted up.
|
Re: Owen's C10
3 Attachment(s)
front sway bar, and pie cut the uppers...
|
Re: Owen's C10
4 Attachment(s)
set the cab back on for looks...
|
Re: Owen's C10
4 Attachment(s)
I didn't like the look of the way the drip rails turned out, so I did it over.
|
Re: Owen's C10
3 Attachment(s)
painted the bottom of the door to see what that would look like...
|
Re: Owen's C10
5 Attachment(s)
today I made some axle mounts to replace the rusted out ones...made them out of some scrap 2x4, and with an extra 2" of drop built in..I still have to finish them, but that's another day...
|
Re: Owen's C10
4 Attachment(s)
I spent the weekend welding, made some fillers for the firewall and welded in all the holes that I wouldn't be needing...
|
Re: Owen's C10
5 Attachment(s)
a few more..
|
Re: Owen's C10
1 Attachment(s)
gas filler hole....
|
Re: Owen's C10
4 Attachment(s)
fixed the rust in the dash and the corner of the windshield....
|
Re: Owen's C10
2 Attachment(s)
....
|
Re: Owen's C10
2 Attachment(s)
welded the cab seam.
|
Re: Owen's C10
4 Attachment(s)
.......
|
Re: Owen's C10
4 Attachment(s)
not a very productive weekend, but we still managed to do a few little things...like shave the defrost vents and speaker grill in the dash...
|
Re: Owen's C10
2 Attachment(s)
...thought I'd practice on the old bed side instead of ruining a good one. definitely made a few mistakes, but now I know what "not" to do next time!
|
Re: Owen's C10
4 Attachment(s)
the results...
|
Re: Owen's C10
3 Attachment(s)
road trip!...took the day off Friday to go pick up the cab floor.
|
Re: Owen's C10
1 Attachment(s)
a few of the trucks sitting at bill's truck shop...
|
| All times are GMT -4. The time now is 05:36 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com