The 1947 - Present Chevrolet & GMC Truck Message Board Network

The 1947 - Present Chevrolet & GMC Truck Message Board Network (https://67-72chevytrucks.com/vboard/index.php)
-   The 1960 - 1966 Chevrolet & GMC Pickups Message Board (https://67-72chevytrucks.com/vboard/forumdisplay.php?f=6)
-   -   62 V8 starter (https://67-72chevytrucks.com/vboard/showthread.php?t=851841)

62 Barnfind 04-06-2024 07:35 PM

62 V8 starter
 
I’m trying to find the correct starter for the 60-62 V8 bell housing. I purchased one off Rock auto but it’s doesn’t fit. I had the grind down the inside of the bell housing for it to clear and fit right. It engages the flywheel but won’t retract after power is disengaged. Just wondering if it’s a bad starter or is the clearance off? Does anyone have the right part number for the correct one?

Chevy Fleetside 04-08-2024 10:21 AM

Re: 62 V8 starter
 
Is it for an automatic or manual trans?

62 Barnfind 04-13-2024 04:51 PM

Re: 62 V8 starter
 
Quote:

Originally Posted by Chevy Fleetside (Post 9302482)
Is it for an automatic or manual trans?

Manual

bhap 04-13-2024 07:24 PM

Re: 62 V8 starter
 
I think you need a starter with a cast iron nose cone - not the more common alloy/aluminum. I have a 5.7 Vortec with the 62 V-8 bellhousing and use a cast iron nose starter that mounts to the block. I have a 3 speed manual transmission and a 168 tooth flywheel. I think you can swap noses between starters so if you have a starter repair shop, they may be able to convert yours. I'm pretty sure it is the same if you are bolting the starter to the bellhousing - you need the "pointy", narrower cast iron nose. Good luck!

62 Barnfind 04-14-2024 10:22 AM

Re: 62 V8 starter
 
Quote:

Originally Posted by bhap (Post 9304082)
I think you need a starter with a cast iron nose cone - not the more common alloy/aluminum. I have a 5.7 Vortec with the 62 V-8 bellhousing and use a cast iron nose starter that mounts to the block. I have a 3 speed manual transmission and a 168 tooth flywheel. I think you can swap noses between starters so if you have a starter repair shop, they may be able to convert yours. I'm pretty sure it is the same if you are bolting the starter to the bellhousing - you need the "pointy", narrower cast iron nose. Good luck!

That’s the problem. Trying to find that one. I opened the bell housing up to fit the one I have. The starter turns fine but won’t retract back when the power is off. I think I have a weak starter.

bhap 04-14-2024 07:08 PM

Re: 62 V8 starter
 
Do you have clearance between the starter gear and the flywheel? I don’t remember spec, but there was a trick involving the right size drill bit to confirm sufficient gap. You may need to shim the starter. Does the gear return ok when starter is not installed ?

dmb 04-14-2024 09:57 PM

Re: 62 V8 starter
 
https://www.ebay.com/itm/30502417922...3ABFBMjta-99tj

AcampoDave 04-14-2024 10:38 PM

Re: 62 V8 starter
 
I used a starter like this https://www.jegs.com/i/JEGS+Performa...hoCPyoQAvD_BwE it fit my cast iron bell housing and bolted to my block. I did have to do a minor mod to my tin flywhell cover but it was no biggie.

62 Barnfind 04-18-2024 07:49 AM

Re: 62 V8 starter
 
Quote:

Originally Posted by dmb (Post 9304543)

I have that starter. Everything aligned and turns great. Gear won't retract when power is off.


All times are GMT -4. The time now is 07:44 PM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com