The 1947 - Present Chevrolet & GMC Truck Message Board Network

Page 1 of 2

Show 40 post(s) from this thread on one page

The 1947 - Present Chevrolet & GMC Truck Message Board Network (https://67-72chevytrucks.com/vboard/index.php)

- Blazer and Suburban Stuff (https://67-72chevytrucks.com/vboard/forumdisplay.php?f=199)

- - MD CST rear panel brackets (https://67-72chevytrucks.com/vboard/showthread.php?t=806351)

richard2717

05-16-2020 11:44 AM

CST rear panel brackets

4 Attachment(s)

I have original 6 brackets. Heavy surface rust but seem to clean up decent.

$75 shipped

Original brackets are SOLD but new ones available below

.

Harold Holbrook

05-16-2020 12:03 PM

Re: CST rear panel brackets

I need the ones that goes on the floor and by the tail gate.

72 Jimmy Power

05-16-2020 12:49 PM

Re: CST rear panel brackets

How about $65? I'll take them. Thanks.

richard2717

06-16-2020 12:40 PM

Re: CST rear panel brackets

Ttt can also make new 6 pc perimeter angle set to go with them for extra$

harrisoncole4

06-16-2020 02:37 PM

Re: CST rear panel brackets

Correct me if I am wrong, but at some point you had posted a thread stating that you were making reproduction brackets for the cst panels. Do you have a link for that thread?

wesmigletz

06-16-2020 02:42 PM

Re: CST rear panel brackets

I am interested in a complete set, too, if available. Are you reproducing these? I need them for a non-CST Blazer.

richard2717

06-16-2020 02:43 PM

Re: CST rear panel brackets

Quote:

Originally Posted by harrisoncole4 (Post 8758782)

Correct me if I am wrong, but at some point you had posted a thread stating that you were making reproduction brackets for the cst panels. Do you have a link for that thread?

Was not me, but they are simple enough to make other than the stamped stiffeners.

KevJim72

06-16-2020 10:53 PM

Re: CST rear panel brackets

I'll get in line for these. I also need a complete set but interested in these.

richard2717

06-17-2020 10:46 AM

Re: CST rear panel brackets

4 Attachment(s)

guys,
here is what I came up with this morning. I made 2 sets but have plenty of material to do more if needed. I figure $135 per set of 12 pcs shipped in lower 48. elsewhere would be a little more to cover added shipping costs. I can punch holes in them but that would add to the cost and they are easy enough to drill. The original brackets feel like 20 ga and are real flimsy. I made these out of 18 ga which stiffened them up quite a bit.

.

harrisoncole4

06-17-2020 10:49 AM

Re: CST rear panel brackets

Nice work! I'll take a set.

wesmigletz

06-17-2020 11:14 AM

Re: CST rear panel brackets

They look good. I'll take a set. Thank you

richard2717

06-17-2020 11:17 AM

Re: CST rear panel brackets

Quote:

Originally Posted by harrisoncole4 (Post 8759216)

Nice work! I'll take a set.

Sent PM for address

Quote:

Originally Posted by wesmigletz (Post 8759228)

They look good. I'll take a set. Thank you

PP link is in my signature below. Thanks

wesmigletz

06-17-2020 11:26 AM

Re: CST rear panel brackets

Quote:

Originally Posted by richard2717 (Post 8759233)

Sent PM for address

PP link is in my signature below. Thanks

Thank you, I will send payment and my address this afternoon.

KevJim72

06-17-2020 12:33 PM

Re: CST rear panel brackets

I'll take the original 6 piece set if you still have it. Thanks.

wesmigletz

06-17-2020 01:09 PM

Re: CST rear panel brackets

I sent payment via paypal and sent you a PM with my address

Thank you

richard2717

06-17-2020 01:10 PM

Re: CST rear panel brackets

Quote:

Originally Posted by wesmigletz (Post 8759301)

I sent payment via paypal and sent you a PM with my address

Thank you

Got your payment and they will ship tomorrow.

Thanks
Richard

richard2717

06-17-2020 01:14 PM

Re: CST rear panel brackets

Quote:

Originally Posted by KevJim72 (Post 8759066)

I'll get in line for these. I also need a complete set but interested in these.

Quote:

Originally Posted by KevJim72 (Post 8759287)

I'll take the original 6 piece set if you still have it. Thanks.

Ok do you want just the original six brackets or do you need angles as well? Do you still want an extra "new" set? I can knock some off for shipping. LMK

Thanks
Richard

KevJim72

06-17-2020 02:22 PM

Re: CST rear panel brackets

Quote:

Originally Posted by richard2717 (Post 8759303)

Ok do you want just the original six brackets or do you need angles as well? Do you still want an extra "new" set? I can knock some off for shipping. LMK

Thanks
Richard

PM sent

richard2717

06-17-2020 05:12 PM

Re: CST rear panel brackets

Quote:

Originally Posted by KevJim72 (Post 8759336)

PM sent

Got your payment and they will ship tomorrow morning. Thanks

richard2717

06-18-2020 10:51 AM

Re: CST rear panel brackets

All 3 sets shipped this morning. I do have a couple sets left.

shume

06-22-2020 10:43 PM

Re: CST rear panel brackets

Just sent pay pal for a set.
Thanks

wesmigletz

06-23-2020 12:36 AM

Re: CST rear panel brackets

Got mine on Saturday. Thank you for shipping them so quickly.

richard2717

06-23-2020 07:48 AM

Re: CST rear panel brackets

Quote:

Originally Posted by shume (Post 8762331)

Just sent pay pal for a set.
Thanks

I will try to get them out today. Thanks

Quote:

Originally Posted by wesmigletz (Post 8762388)

Got mine on Saturday. Thank you for shipping them so quickly.

Thanks for letting me know

richard2717

06-28-2020 01:17 PM

Re: CST rear panel brackets

Still have a few sets

richard2717

07-15-2020 02:44 PM

Re: CST rear panel brackets

I only have one set left at the moment

All times are GMT -4. The time now is 07:41 PM.

Page 1 of 2

Show 40 post(s) from this thread on one page