BBC Turbo 400 to LT4 T56
I have sold the complete driveline from my 71. Radiator to rearend , pan to carb ....gone. It will help cover a small portion of the cost of the conversion. I may regret that decision one day.
....There is no turning back. |
Re: BBC Turbo 400 to LT4 T56
1 Attachment(s)
The victim.
|
Re: BBC Turbo 400 to LT4 T56
2 Attachment(s)
Made a little headway. Got the trans, seat, carpet and steering wheel out too.
|
Re: BBC Turbo 400 to LT4 T56
4 Attachment(s)
After a couple tries I got the motor sitting in place and harness laid in. I built a pair of custom motor mount brackets to get it sitting where I want. Good news is I can use the factory oil pan. Bad news the oil cooler hits the crossmember so it has to go. I couldn't find anyone building a remote oil cooler set up for this oil pan yet so I cut the stock one apart and added some fittings to remote mount something later.
|
Re: BBC Turbo 400 to LT4 T56
2 Attachment(s)
.....Feels like I am talking to myself.
I've got a factory high hump so I am lucky there. Time to molest it . Yaaa !, the wiring harness is long enough, I can hide the phone book ECM under the seat! Just need to figure out a grommet set up for the harness to come through the floor |
Re: BBC Turbo 400 to LT4 T56
1 Attachment(s)
Took a knife to the harness. One wrong move and it can spell disaster.The GM tape that holds it together is high quality! Changed up the corrugated covering to a smaller weaved cover and was able to hide some of the wiring
|
Re: BBC Turbo 400 to LT4 T56
2 Attachment(s)
Needed a way to plug the water pump outlet for the oil cooler so I took the OEM fitting and welded a flange on to it so I could add a add a temp sensor. It's super tight. I just managed to fit it then there.
|
Re: BBC Turbo 400 to LT4 T56
1 Attachment(s)
Hopefully the Dakota dash will connect seamlessly to the ecm and save me a few wiring headaches.
|
Re: BBC Turbo 400 to LT4 T56
Very Nice truck and extremely clean build!
|
Re: BBC Turbo 400 to LT4 T56
I'm in for this build. Very cool.
|
Re: BBC Turbo 400 to LT4 T56
if you've got the bim module from dakota, its a super easy install. Instead of using the plug in from the obd2 connector i purchased the same style connector from radio shack and hard wired them from the back of the obd2 to the bim module. Much cleaner look. 1 thing to note though is that you must unplug the gauges when using hp tuners. It won't load up as it recognizes the split in signal. Took me awhile to figure that one out....
|
Re: BBC Turbo 400 to LT4 T56
1 Attachment(s)
Quote:
Drive Junkie supplied the front serpentine set up. The fit and finish is awesome. I went with it because I prefer the blower to have its' own belt. I am scratching my head how to connect the 2 wire ALT feed that Gm supplies in the engine harness. The alternator supplied by Drive Junkie is a one wire set up. |
Re: BBC Turbo 400 to LT4 T56
Nothing exciting today. I extended the fuel pump and fuel pressure wires and got them run to the back along with my taillight harness. Modified my trans crossmember to match the new location of the mount for the T56 magnum. Set the new rad in to get a feel for how much room I 'll have for the shroud,fans and air intake.
|
Re: BBC Turbo 400 to LT4 T56
1 Attachment(s)
Not much to report. Moved my trans mount and got it bolted back in. It ended up moving forward a couple inches in relation to the old T400 location.
Gm warns that the LT4 doesn't create much vacuum so I have been messing with a hydroboost from a 03 Mustang trying to determine if I can make it work in the truck. |
Re: BBC Turbo 400 to LT4 T56
Astro Van ones work well, PM LS1nova71 Eric is a bottomless pit of info.
|
Re: BBC Turbo 400 to LT4 T56
Cpp makes a real nice hydroboost kit called street beast I have it on my 71 with ls swap.
|
Re: BBC Turbo 400 to LT4 T56
1 Attachment(s)
Hydroboost from cpp
|
Re: BBC Turbo 400 to LT4 T56
Thats going to be one wild ride!:metal:
|
Re: BBC Turbo 400 to LT4 T56
1 Attachment(s)
This badboy arrived today.
Wavetrac with 3.50 gears and 35 spline |
Re: BBC Turbo 400 to LT4 T56
Nice that should hold up to the 650 hp !
|
Re: BBC Turbo 400 to LT4 T56
4 Attachment(s)
Out with the old and in with the new. No drama. I like when that happens.
|
Re: BBC Turbo 400 to LT4 T56
That's some great quality parts going into a slick truck.
|
Re: BBC Turbo 400 to LT4 T56
5 Attachment(s)
I unboxed and bolted up the headers. We got them from Ultimate. They were designed for a 67-69 Camaro LT4 swap. They work pretty well. I had to massage the passengerside engine pedestal a little bit but other than that easy peasy. Tons of room to slide them in.
The collector does hang about 1/2 inch below the frame but I can live with that. |
Re: BBC Turbo 400 to LT4 T56
1 Attachment(s)
Got the 03 Mustang hydroboost adapter plate made.
....hope it works.Just need to build the linkage. |
Re: BBC Turbo 400 to LT4 T56
Mounted up the new condenser. Now time to figure out the heat exchanger mount for the supercharger.
|
All times are GMT -4. The time now is 06:45 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com