Re: LS factory cruise control hook up
 

I grabbed two 4 wire switches from the junk yard.. but I couldn't find a good lever assembly....

Re: LS factory cruise control hook up
 

What kind of column do you have?
Posted via Mobile Device

Re: LS factory cruise control hook up
 

Thanks you have answered many questions!

Re: LS factory cruise control hook up
 

Mine is hooked up and working! now for a long road trip!

Re: LS factory cruise control hook up
 

Right on!
Posted via Mobile Device

Re: LS factory cruise control hook up
 

Do I need to wire just the TAC or the PCM also?

Re: LS factory cruise control hook up
 

Just the TAC, provided your PCM is already wired up, brake light switch input, that sort of thing.

Re: LS factory cruise control hook up
 

Aren't those levers pretty expensive. IIRC those are the ones LMC sells for $230. I have one that came out of a 1980 Suburban but it is pretty rough. Where did you get yours and where did you get the sheet of labels???

http://67-72chevytrucks.com/vboard/a...1&d=1330398300
http://67-72chevytrucks.com/vboard/a...1&d=1330398300

Re: LS factory cruise control hook up
 

I don't know about LMC, I'll have to check my catalog when I get home. I think they are usually found in '81-82 trucks, but they're usually only a 3 wire switch so you have to change the switch inside of if with a 4 wire. Although I have seen a couple of them with the 4 wire switch already in them.

I had the labels made, if you want one, id sell you one for. $7 shipped.
Posted via Mobile Device

Re: LS factory cruise control hook up
 

I will probably take you up on that, let me dig up my old lever and see how many wires it has and if it is usable. Thanks!

Re: LS factory cruise control hook up
 

Subscribed!

Re: LS factory cruise control hook up
 

so in order to run cruise with an on off toggle and a momentary switch i need to run a jumper wire with 12v from the on off switch when its on to the middle of the momentary switch ?

Re: LS factory cruise control hook up
 

I have a toggle switch that provides 12+ to terminal A to turn the unit on/off.
I have a momentary push button that provides 12+ to terminal B when pushed to set cruise. If i hold the button in it will coast until i release the button. Terminal C i remove, everything else is the same as posted.

Re: LS factory cruise control hook up
 

:DI will probably end up with a Summit Racing aftermarket column.... for now I have the factory NON-tilt auto column shift.... So I need the one with the hole for the screw....

What did these come out of again.... 3 or 4 wire doesn't matter...

Re: LS factory cruise control hook up
 

I found my lever and it is a 3 wire not to mention its in pretty bad shape. I'm going to hold off on getting a sticker from you until I can find a 4 wire setup or at least a nicer 3 wire to convert. I might even get a new one, who know.

Re: LS factory cruise control hook up
 

They are usually found in "81 vans and '81-82 trucks.
How bad is it? I might be able to fix it, I've fixed some pretty nasty looking ones. Or if you get a new one and the old one isn't all that bad, I might be interested in it.

Re: LS factory cruise control hook up
 

Hey guys my cruise lever has 4 wires at the connecter Red, Brown, Green, Yelow. Pretty sure it is from Van tilt column.
I need help making the conections to my '99 Silverado cruise module.
I have transplanted the '99 5.3 / 4l60e, fuse block, and instrument cluster.

Appreciate your help
http://67-72chevytrucks.com/vboard/a...1&d=1333917353
Just need help with figuring out wich wires go were.

'99 Crusie Module Connecter:
A Gry 397 On switch Output
B DkBlu 84 Set/Coast switch signal
C Gry/Blk 87 Resume/Accel switch signal
D Brn/Wht 379 Clutch pedal switch output
E Blk/Wht 451 Engine control module ground
F Brn 41 Fused Ignition3 Output
G LtBlu 1320 Fused stop lamp feed
H Not used
(no "I" position)
J LtBlu/Blk 396 Signal engage
K DkGrn/Wht 817 VSS

Re: LS factory cruise control hook up
 

That's a switch from an aftermarket cruise control. They are usually normally closed switches and you will need to use relays to reverse them. Ackattack's thread that I have linked in my first post has instructions on how to do it. As for what wires to use for each function, you'll just have to test them to find out. You can do it with a DVM or a test light and a battery.
Posted via Mobile Device

Re: LS factory cruise control hook up
 

I got mine wired up _ but it is not working. Mine is DBW, does it need to see speedo input to work.

Re: LS factory cruise control hook up
 

It has to have a VSS signal if that's what you're asking. You don't need an actual speedometer hooked up. Do you have both brake switch inputs hooked up? And do you have brake lights? It needs to see ground through them.
Posted via Mobile Device

Re: LS factory cruise control hook up
 

Pic for farmtrucks. This is a factory pigtail for the cruise switch. The gray wire is the on/off and goes to pin 14 on the TAC. Green is resume/accel and goes to pin 5. Blue is set/coast and goes to pin 4. Pink is the ignition power to the switch.

Re: LS factory cruise control hook up
 

I have a 2005 LS2 with E40 computer DBW. Cruise does not work.

I think the problem is that the cruise is interlocked with the e-brake. The ECM has to see that the e-brake is off for the cruise to engage. (I know this is true on my 08 LS3). Problem is that the BCM reads the e-brake switch and puts the message on the low speed serial bus which the ECM reads.

(The same problem occurs for the case learn procedure. The TECH II has to see that the e-brake is on in this case for it to run the procedure.)

I am in the process of trying to get a BCM wired up with a toggle switch for the e-brake. No success yet.

Has anyone gotten cruise to work with DBW???

TR

Re: LS factory cruise control hook up
 

Would 1 of these type cruise levers work with 01 6.0 DBW and cruise module? http://www.ebay.com/itm/1971-72-CADI...5e7c01&vxp=mtr

It only has 3 wires, black, blue, and brown.

Re: LS factory cruise control hook up
 

It might, but you would only be able to set it, you wouldn't have an on/off or accel/resume.
If you want one of the ones I have pictured I have a few I would sell.
Posted via Mobile Device

Re: LS factory cruise control hook up
 

Ok. Thanks. I would be happy just pushing the button and the cruise would be set. I don't need the fancy on/off or accel/resume.