$1.00 60-63 C10 Cab Cuts
 

Just got this cab. Not sure if any of you guys may need some cab cuts. Everything is available except for the BBW.

$1.00 plus the cost of shipping to you.

Re: $1.00 60-63 C10 Cab Cuts
 

Whats radio area look like?

Re: $1.00 60-63 C10 Cab Cuts
 

lower A pillar area, inside the cab about level with the dashboard

Re: $1.00 60-63 C10 Cab Cuts
 

Here is a picture

Re: $1.00 60-63 C10 Cab Cuts
 

Dm me a number and I’ll send you a picture of it

Re: $1.00 60-63 C10 Cab Cuts
 

Here are some pictures

Re: $1.00 60-63 C10 Cab Cuts
 

Hi 67 I'll take the transmission firewall section and the radio delete plate. Thanks.

Re: $1.00 60-63 C10 Cab Cuts
 

Ill take this section right here please. Shipping to 37843. Let me know how you want paid.

Re: $1.00 60-63 C10 Cab Cuts
 

I will get it cut on Friday and get you a quote for shipping. Hopefully it will fit a Priority box

Re: $1.00 60-63 C10 Cab Cuts
 

Sounds good..

Re: $1.00 60-63 C10 Cab Cuts
 

Speaker bracket happen to be still there? Defrost vents?

Re: $1.00 60-63 C10 Cab Cuts
 

Not too familiar with the 1st gen c10s. Where would the factory bracket be?

Re: $1.00 60-63 C10 Cab Cuts
 

The radio delete has a bullet hole and the transmission section was hacked up

Re: $1.00 60-63 C10 Cab Cuts
 

It right under that grate. Held on with a bolt to the cab.

Re: $1.00 60-63 C10 Cab Cuts
 

Looks something like this to the right.

Re: $1.00 60-63 C10 Cab Cuts
 

Any rust through on the upper corners of the windshield area? I need both sides inside and out. Also, if it has the passenger side sun visor bracket, I could use that area as well

Re: $1.00 60-63 C10 Cab Cuts
 

I would take a 3 of pieces of the stamped back of the cab highlighted, say about 1 inch on each side of the bends and about 6 inches up, so they can fit in a priority box like Small Box 8 11/16" x 5 7/16" x 1 3/4" $7.65
or Medium Boxes 11 1/4" x 8 3/4" x 6" or 14" x 12" x 3 1/2" $13.20 , thanks Joe

Re: $1.00 60-63 C10 Cab Cuts
 

No passenger side visor

Re: $1.00 60-63 C10 Cab Cuts
 

That's ok. If the rust isn't completely through on either side, I need both of these circled sections. I have not cut into my truck yet to see the extent of the rust, but I know it looks pretty bad from the outside, especially on the passenger side. Just to be on the safe side, if you are willing to cut out the inside section with it, that would be great. I don't need the roof skin though. Seam sealer deteriorated and let water rust out the upper lip areas.

My zip is 30188

Thanks!

*Edit* I will go check on my cab in a couple minutes to see if I need the inside part or not.

Re: $1.00 60-63 C10 Cab Cuts
 

I'll start working on the cab cuts tomorrow.

Re: $1.00 60-63 C10 Cab Cuts
 

I checked my cab on the inside. It looks ok. It's the outside part that I know has some big holes in it

Re: $1.00 60-63 C10 Cab Cuts
 

How much of the back window are you keeping? The whole panel, or are cuts along the bottom of the cab at the pinch weld available?
I need about two inches high, along the driver's side. It's been a while since I've seen the cab--if you're good with cutting that area, I'll go find out what I need exactly.
-Brad

Re: $1.00 60-63 C10 Cab Cuts
 

I’d like to have one side of the dash, for the “hump” portion on top.

Re: $1.00 60-63 C10 Cab Cuts
 

Either side of the dash will be fine for my purposes, whichever is the straightest.

Re: $1.00 60-63 C10 Cab Cuts
 

Can i get this section cut out please? let me know how much to 94513. Thanks