Re: LS Swap Electric Speedo face and template
 

i will take two of these if you make anymore.

Re: LS Swap Electric Speedo face and template
 

I would as well!

Re: LS Swap Electric Speedo face and template
 

I need something like this for a 73-87 using the earlier speedo

Re: LS Swap Electric Speedo face and template
 

Put me in line for a kit if/when you make more. Thanks.

Re: LS Swap Electric Speedo face and template
 

I currently have 2 kits left, going to have to get some more made up. I sent you a PM.

Re: LS Swap Electric Speedo face and template
 

I'll take one..

Re: LS Swap Electric Speedo face and template
 

Thanks. Paypal sent.

Re: LS Swap Electric Speedo face and template
 

PMs sent

Re: LS Swap Electric Speedo face and template
 

ls1nova71

Would you mind going over what I would need in addition to your kit.
I would assume I would have to find s10 speedo.

I am running a GM 'connect and cruise' in my 70 C10 stepper.

Thanks

Re: LS Swap Electric Speedo face and template
 

Ls1nova71 didn't receive the pm.

Re: LS Swap Electric Speedo face and template
 

Well, I thought I sent it, but don't see it either. I sent it just now.

Re: LS Swap Electric Speedo face and template
 

I'm not super familiar with the C&C engine combo, but I don't think that package is set up for a regular electric speedometer being that it is a GenIV engine. Do you have a wire in your harness that says it's foe a speedo?

Re: LS Swap Electric Speedo face and template
 

Yes I am currently running a Dakota Digital box to drive the speedo. I have seen signs of it studdering lately and I am afraid it might be on the way out. It uses a wire marked for the speedo to get pulses.

Re: LS Swap Electric Speedo face and template
 

Ok, so apparently that system does have a speedo output. I would check your install instructions and if it is putting out a 4000ppm signal like the older engines do, then it would work. As for what else you need other than my kit, depends on how much work you want to do. I include the face, the stencil for painting the numbers on the lens, and 2 paper templates for making the mounting plate and rear cover box. If you dont want to make those 2 parts, CaptainFab was making them at one time and may still have them, but you'd have to check with him to be sure. Other than that, you'll need an S10 speedo obviously, and sockets for the lights, a small LED for the high beam indicator and I usually put in a plug so the cluster can be unplugged to remove it when necessary. It's all laid out in detail in the electric speedo thread along with directions on how to do it.

Re: LS Swap Electric Speedo face and template
 

Pm sent

Re: LS Swap Electric Speedo face and template
 

Interested if you have any made? May need 2.

Re: LS Swap Electric Speedo face and template
 

I want one. PM me and I will send you the payment.
Thanks.

Re: LS Swap Electric Speedo face and template
 

PM sent

Re: LS Swap Electric Speedo face and template
 

Do you have a wiring schematics for the cluster with the speedometer in it?

Re: LS Swap Electric Speedo face and template
 

Are you talking about a schematic for a '96 S10? What exactly do you need to know?

Re: LS Swap Electric Speedo face and template
 

I'm sorry for sending you this. I found the link where you had posted the wiring for the 71 C10 speedo. Thanks again for all your help.

Re: LS Swap Electric Speedo face and template
 

If you have any currently, I will take one. Shoot me a PM.

Re: LS Swap Electric Speedo face and template
 

I’ll take a kit. Thanks!
Andrewortiz54@gmail.com
4084696001
Posted via Mobile Device

Re: LS Swap Electric Speedo face and template
 

I'll take a kit

Re: LS Swap Electric Speedo face and template
 

If these kits are still available, I would like one please.