Turning Issue. SOLVED!! Center-link
4 Attachment(s)
I have a 72 5 lug disc brake set up on my 70 C10. Way back I had ECE 2 1/2" Drop Spindles installed ... I have rubbing issues where the truck has a short turn radius ... when I turn my truck it acts like it’s a 4x4 and I get that 4x4 turning hop feeling. If I go with a 2: Drip Spindle ... in theory that should raise the front end about 1/2" which is all the clearance I need. Your thoughts … No its not the wheel hitting as I have done the grinding to make clearance. Check out the pics. Thanks
PS: I have a factory 402BB if that makes a difference... |
Re: 2/1"Drop Spindle Question - Turning Issue.
IMHO using lowering coil springs vs drop spindles is the way to go
https://www.cjponyparts.com/ridetech...20Search%20Ads |
Re: 2/1"Drop Spindle Question - Turning Issue.
Quote:
I have a factory 402BB if that makes a difference... |
Re: 2/1"Drop Spindle Question - Turning Issue.
I think maybe your center link is on backwards(?) I'm not sure.. but I think it goes castle nuts out. That would definitely impact your turning radius.
|
Re: 2/1"Drop Spindle Question - Turning Issue.
Quote:
It very well could be. This truck was redone years ago but I only started driving it a couple years ago and I am now trying to fine tune it. |
Re: 2/1"Drop Spindle Question - Turning Issue.
I can't tell if the centerlink is backwards, but the tie rods are for sure
|
Re: 2/1"Drop Spindle Question - Turning Issue.
Quote:
https://www.summitracing.com/parts/M...engine-type/v8 https://www.summitracing.com/parts/m.../1972#overview |
Re: 2/1"Drop Spindle Question - Turning Issue.
Quote:
Thanks |
Re: 2/1"Drop Spindle Question - Turning Issue.
First thought I had was, "Shouldn't the tie rods be coming in from the rear with the nuts out the front?" We recently had another member on here with turning issues that fixed up.
|
Re: 2/1"Drop Spindle Question - Turning Issue.
Quote:
It needs to be removed and swapped end for end. Inner tie rod nuts need to be on the FRONT SIDE of the centerlink. |
Re: 2 1/2 " Drop Spindle Question - Turning Issue.
Thanks All
Can someone send me a picture ... Thanks |
Re: 2 1/2 " Drop Spindle Question - Turning Issue.
1 Attachment(s)
I could have sworn I had photos of mine but could not find one. Here is one from the web. Driver's side but you can see how the inner tie rod comes in from the rear of the center link.
|
Re: 2 1/2 " Drop Spindle Question - Turning Issue.
Yup, just went through this. They are backwards. It will drive so much better you will not believe it. Toe in will have to be adjusted. Mine was way out after I swapped the center link. You will have to turn the wheel hard over to get it installed as there isn't enough room to install the center link with the wheels straight. Per LocDoc's recommendations install 90 deg fittings to allow for greasing if they are not already installed. Remember "NUTS FORWARD" is how it's installed.
Cheers. |
Re: 2 1/2 " Drop Spindle Question - Turning Issue.
Folks ... this is a GREAT help. Thanks :metal:
|
Re: 2 1/2 " Drop Spindle Question - Turning Issue.
DeWayne, I agree with everyone else here. Swap the center link WES
|
Re: 2 1/2 " Drop Spindle Question - Turning Issue.
Quote:
Do you all think the the tie rods are also backwards? |
Re: 2 1/2 " Drop Spindle Question - Turning Issue.
Quote:
But most likely you will need to adjust the toe. Get the wheels as straight as possible and then take it to get the front end re-aligned. |
Re: 2 1/2 " Drop Spindle Question - Turning Issue.
Again folks ... you all have been a great help. I take the Circuit Rider in this Friday and all the work needed will be done and I look forward to being able to making turns. :metal:
|
Re: 2 1/2 " Drop Spindle Question - Turning Issue.
FYIO, I had my truck aligned twice and the alignment guy didn't catch it issue. They even drove the truck before and after. So I have three $90 alignments! It was my bad though. I knew it was possible and my research was inadequate. You will like your truck a lot more after it's back to factory.
cheers. |
Re: 2 1/2 " Drop Spindle Question - Turning Issue.
Quote:
|
Re: 2 1/2 " Drop Spindle Question - Turning Issue.
I just got a call from the shop that does my work on the C10 ...they changed out the Center-link as it was installled backwards and they said - WOW. It is like driving a new truck. They also said the inside wheel clearance is vastly improved. I hope to pick it up today. Can't wait to drive it.
Again a great big thank you for steering :lol: me in the right direction. |
Re: Turning Issue. SOLVED!! Center-link
Good to hear. Cruise on brutha!
|
All times are GMT -4. The time now is 04:21 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com