keyparts, triplus, auto metal direct?
keyparts, triplus, auto metal direct. Fenders...are they all the same? I know the fender thing has been bashed a million times. I want to buy new fenders if, at least I use them for patch panels, if they don't fit very well. Are the new keyparts "zinc" gm cert parts better than the amd triplus fenders? AMD prices seem to be a little better, but they don't claim the zinc primer etc. But, they have told me that they are triplus fenders.
|
Re: keyparts, triplus, auto metal direct?
2 Attachment(s)
TriPlus = Make
KeyParts = Distributor AMD = Reseller Pisc show fitment of a NEW Triplus fender and NOS fender.........I currently will not sell Triplus fenders due to this and dont even think about a Gordans fender...lol.......... |
Re: keyparts, triplus, auto metal direct?
1 Attachment(s)
Gordans fender....
|
Re: keyparts, triplus, auto metal direct?
I was hoping to use the bottom cups and bottom rears to patch my gm fenders. Mine aren't horrible but the cup and inner cup passenger is bad and drivers side has rust at very bottom front and back.
|
Re: keyparts, triplus, auto metal direct?
Quote:
|
Re: keyparts, triplus, auto metal direct?
1 Attachment(s)
Quote:
It was way to far off to "hammer" it back. The entire nose is wrong.......The point is in the right location, its the detail line down the side that is set back to far by aprox 3/8". Drivers side fitment is the same......3 Different trucks, 3 different grills, and 3 different core supports.....all fit the same........ I reached out to my supplier and also a few others that buy, sell and install these with little response...... :( |
Re: keyparts, triplus, auto metal direct?
Yeah they all say guaranteed to fit. But I don't see anyone saying . You buy these and they don't fit, we will pay return shipping and fully refund.
|
Re: keyparts, triplus, auto metal direct?
Quote:
|
Re: keyparts, triplus, auto metal direct?
I have to modify the summit answer...they took back a bumper that was free shipping, don't know their policy on truck freight and the fender from them has a freight charge.
|
Re: keyparts, triplus, auto metal direct?
Anybody know if the 67-68 fenders have these same problems?
|
Re: keyparts, triplus, auto metal direct?
I have not seen any problem with mine on my 68, I had them all mounted up at one time. :mm:
|
Re: keyparts, triplus, auto metal direct?
2 Attachment(s)
Nothing ever seems to line up when it comes to aftermarket patch panels. I just purchased a lower inner door bottom patch repair panel for my 72 and the factory crease along the inner does not match the new panel. Being that the panel is about 18 gauge, i dont have the proper tools to make the bead and doesnt make sense picking a bead roller from eastwood for one door. decided to add some quick pics, i laid down the new panel and then the old panel on top to show how bad the new panel is. it's not even close to replicating the bead from factory. I called Sherman, AMD, and some other places and yes looks like triplus keypart are the only ones that makes panels. stuck with his project now. AMD was kind enough to refund me the money on this hacked up panel, so i give them that at least.
|
Re: keyparts, triplus, auto metal direct?
Yes, the door inners absolutely suck. They are not even close, I used the part of the patch I needed and hammered and dollied it into the shape I needed.
|
Re: keyparts, triplus, auto metal direct?
Quote:
|
Re: keyparts, triplus, auto metal direct?
Quote:
|
Re: keyparts, triplus, auto metal direct?
Quote:
|
Re: keyparts, triplus, auto metal direct?
I bought a right fender and 2 doors aftermarket from a vendor that claims they make their own .....bad mistake none of the 3 will fit any of my trucks/grilles $1000 wasted
|
Re: keyparts, triplus, auto metal direct?
Yeah, even the patches suck.
I had to open this one up on both sides to keep the fender curves correct: http://67-72chevytrucks.com/vboard/a...1&d=1486948251 It was a ton of extra work but worth the effort. http://67-72chevytrucks.com/vboard/a...1&d=1487560122 As mentioned above, the inner door bottoms are garbage. They look the same now as they did 16 years ago. They were so awful. I only used the lower inner corners and one curved section. They lower corners were OK because I shaved them down until they fit, but the curved section I cut out I might as well have started with a flat piece of steel it was so far off. http://67-72chevytrucks.com/vboard/a...1&d=1488005030 http://67-72chevytrucks.com/vboard/a...1&d=1488005140 http://67-72chevytrucks.com/vboard/a...1&d=1489293998 http://67-72chevytrucks.com/vboard/a...1&d=1489293998 http://67-72chevytrucks.com/vboard/a...1&d=1489294827 http://67-72chevytrucks.com/vboard/a...1&d=1491110345 This was my first door repair. It would have been SOOOOOOOOOOOO much easier if the damn thing was correct and I could have welded it in in one piece. |
Re: keyparts, triplus, auto metal direct?
These are old pics, but you CAN get a really good fit on the doors/fenders. I did have to rework the window frames a bit, but other than opening up a bunch of holes and using lots of shims, there was no cut/welding
This is my 67 with Goodmark (Tri-Plus) doors/fenders. http://67-72chevytrucks.com/vboard/a...1&d=1149009279 http://67-72chevytrucks.com/vboard/a...1&d=1149009279 http://67-72chevytrucks.com/vboard/a...1&d=1149009279 http://67-72chevytrucks.com/vboard/a...1&d=1149009487 http://67-72chevytrucks.com/vboard/a...1&d=1149009487 So why am I going back to GM stuff on my truck? I never could get the hood to look as good as it did with the factory fenders... it's almost like the aftermarket fenders are 1/8" "too short" at the top where they curve around. It looks good, but not as good as it could. The doors are flimsy as crap. Like really flimsy. The doors were improved the past couple of years with much thicker metal, but I've read complaints where the fit has now gone down with the thicker doors. |
Re: keyparts, triplus, auto metal direct?
Quote:
Looks really good. the door gaps are very uniform. When are you converting it back to GM stuff? |
Re: keyparts, triplus, auto metal direct?
:lol:
When I ever find time. I finally finished my home remodel, now starting a 30x50 shop for my toys. Oh, and I picked up a 68 Firebird that doesn't run... the C10 is in one piece and runs, it's hard to take her back apart. |
All times are GMT -4. The time now is 02:08 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com