The 1947 - Present Chevrolet & GMC Truck Message Board Network

The 1947 - Present Chevrolet & GMC Truck Message Board Network (https://67-72chevytrucks.com/vboard/index.php)

- The 1969 - 1972 Blazers and Jimmys Message Board (https://67-72chevytrucks.com/vboard/forumdisplay.php?f=36)

- - Jerry can holder (https://67-72chevytrucks.com/vboard/showthread.php?t=772858)

NJKelly

10-08-2018 05:15 PM

Jerry can holder

3 Attachment(s)

Have the Swing Away tire carrier and the bracket for the Jerry can. I need a couple other pieces to complete it pictures attached. Anyone has some let me know appreciate it thanks

hemi43

10-08-2018 09:16 PM

Re: Jerry can holder

2 Attachment(s)

All you need now is an amp and a sub !!:lol:

NJKelly

10-09-2018 11:47 AM

Re: Jerry can holder

Quote:

Originally Posted by hemi43 (Post 8359964)

All you need now is an amp and a sub !!:lol:

That is cool

Killer Bee

10-09-2018 12:12 PM

Re: Jerry can holder

clever idea, I like it! not sure what pieces you need, but lots of jerry can accessories available out there!

https://www.ebay.com/bhp/jerry-can-holder

good luck!

NJKelly

10-09-2018 02:21 PM

Re: Jerry can holder

Quote:

Originally Posted by Killer Bee (Post 8360379)

clever idea, I like it! not sure what pieces you need, but lots of jerry can accessories available out there!

https://www.ebay.com/bhp/jerry-can-holder

good luck!

Thanks for the info

Mike C

10-09-2018 08:30 PM

Re: Jerry can holder

The hold down you have pictured doesn't look like mine. Mine has a bolt that comes up from the bottom and through the slot in the holder. Then a "C" shaped piece of metal that also has a slot in it goes on the bolt. Then a threaded and bent piece of 1/4" steel threaded 1/4"-20 becomes a wing nut. Should be able to fab it up fairly easy. Probably easier than finding one to buy...

NJKelly

10-09-2018 09:39 PM

Re: Jerry can holder

Quote:

Originally Posted by Mike C (Post 8360712)

Do you have a picture of what you're talking about. The pictures I attached to my original post we're just ones I found off the internet that's not what I have but figured it was what I needed.

Mike C

10-15-2018 01:14 PM

Re: Jerry can holder

I'll try and get one this week for you.

Mike C

10-23-2018 08:03 PM

Re: Jerry can holder

Sorry for the delay, the weather has sucked. The bottom of my carrier is just a lip that the can sits over. So it may be different from yours not sure. But the hold down would be easy to make. I'm pretty sure Bestop the manufacturer of this one, and it has been on my truck since at least 1990.

Note, the big nut in the picture of the hardware is not part of the kit. The aftermarket can (which is really a flip top toolbox) is not as tall as the original GI cans so the nut is just a spacer to get the wingnut (Just a drilled and tapped piece of bent 1/4" strap) high enough to be tightened without it hitting the tube.

https://uniim1.shutterfly.com/ng/ser...338971/enhance

https://uniim1.shutterfly.com/ng/ser...338969/enhance

https://uniim1.shutterfly.com/ng/ser...338969/enhance

https://uniim1.shutterfly.com/ng/ser...338970/enhance

https://uniim1.shutterfly.com/ng/ser...338970/enhance

NJKelly

10-24-2018 09:04 PM

Re: Jerry can holder

Thank You

All times are GMT -4. The time now is 04:24 AM.