The 1947 - Present Chevrolet & GMC Truck Message Board Network

The 1947 - Present Chevrolet & GMC Truck Message Board Network (https://67-72chevytrucks.com/vboard/index.php)
-   The 1967-1972 Chevrolet & GMC Pickups Parts Board (https://67-72chevytrucks.com/vboard/forumdisplay.php?f=8)
-   -   $$ for Garage Renovation/Blazer build Parts Sale (https://67-72chevytrucks.com/vboard/showthread.php?t=329164)

blue_69 02-16-2009 06:37 PM

$$ for Garage Renovation/Blazer build Parts Sale
 
I have to much stuff not enough room and need some extra cash. Please respond in this thread. Most of this stuff will not be worth shipping because of its size. Prices do not include shipping. I have some other odds and ends that i may add as i find stuff so check back.

1.366 Tall Deck Big block. ran great when pulled has been sitting in my shop for 2 to 3 years. NO SHIPPING on this. asking $200 or make offer.
http://www.test.nyhma.org/366 tall deck.JPG

2. pair of 5-lug truck rallys wheels in good shape trim rings are rusty and tires are shot. Dont really want to ship these. $20
http://www.test.nyhma.org/5 lug rally.JPG

3. four Crager soft 8 steel wheels 16x8 6 lug 5inch backspace. I bought these new thinking they would fit my 86. I mounted the tires then discovered the backspacing was too much. They should fit 88 and up. $80
http://www.test.nyhma.org/crager soft8.JPG

4. 67 fender drivers side. has some small dings and some rust started on inside lower corners i did not see any holes but i didnt poke at it. No shipping $25
http://www.test.nyhma.org/68 fender.JPG

5. 69-72 fender drivers side. some small dings what looks like a repiar on inside lower front no holes. No shipping $25
http://www.test.nyhma.org/72 fender.JPG

6. 69-72 fenders. These came off my blazer they have little to no rust. but have some small dents/ warpage and corners were cut to accomadate 35's. No shipping $25 for both
http://www.test.nyhma.org/72 fenders.JPG

7. 69 c/20 long bed 2 wheel drive frame. about 2 inches cut off the front of frame rails and i removed the front crossmember to use on my blazer. will sell parts or whole thing. $25
http://www.test.nyhma.org/69 frame.JPG

8. i have 3 69 grills all in fair to good condition small dings and a couple plastic pieces broken. No shipping. $30 each or $75 all 3
http://www.test.nyhma.org/69 grill best.JPG

blue_69 02-16-2009 06:38 PM

Re: $$ for Garage Renovation/Blazer build Parts Sale
 
9. 2 behind the seat fuel tanks. No shipping $10
http://www.test.nyhma.org/behind seat tanks.JPG

10. front leaf spring w/ spring bracket from 86 4x4 $25
http://www.test.nyhma.org/86 leaf.JPG

11. two steering columns from 75-86 auto non tilt one is newer w/wiper control on directional one is older without. $10 each
http://www.test.nyhma.org/column w-wiper control.JPG

12. 86 wiper cowl $10
http://www.test.nyhma.org/wiper cowl.JPG

13. 86 rear wheel tubs some small dings one has a bolt bronken off in hole $25
http://www.test.nyhma.org/wheel well86.JPG

14. gmc grill no sure what year probably mid 80's bottom mounting tabs broken $10
http://www.test.nyhma.org/gmc grill.JPG

15. Mountain air chisel. got this about a year ago and have only needed it once or twice $40
http://www.test.nyhma.org/mountain air chisel.JPG

too much stuff 02-16-2009 07:04 PM

Re: $$ for Garage Renovation/Blazer build Parts Sale
 
Would you want to sell the blazer emblems if they are decent?

Senator350 02-17-2009 02:38 PM

Re: $$ for Garage Renovation/Blazer build Parts Sale
 
I'd like one of the grills (maybe two)and the air chisel set. Maybe the blazer fenders too, but I need to see them.

I'm about 2hrs east, in the capital district. PM me or email me so we can connect. Jones.comma.Ian@Gmail.com

blue_69 02-17-2009 10:33 PM

Re: $$ for Garage Renovation/Blazer build Parts Sale
 
To Much Stuff: I am keeping that set of emblems for my blazer but i did have an extra set from a parts rig. I looked where i thought they were today and didnt find them. I am planning on going through more stuff this weekend if i find them i will take pics and post them for you.

Senator350: Email sent

70k52wd 02-17-2009 11:49 PM

Re: $$ for Garage Renovation/Blazer build Parts Sale
 
I could use the stock rallies if they are 7in with 3.5 or 3.75in back space, If your willing to ship to 22546.

blue_69 02-19-2009 06:26 PM

Re: $$ for Garage Renovation/Blazer build Parts Sale
 
70k52wd: i measure 7 inch width and 4 inch backspace. If that will work for you i will take the tires off and get a shipping quote.

70k52wd 02-20-2009 09:47 PM

Re: $$ for Garage Renovation/Blazer build Parts Sale
 
Thanks blue but I can't use them... I figured out that I need a 7in with 3 5/8 b/s. Thanks for your time.


All times are GMT -4. The time now is 03:10 PM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com