Parting Out ‘67 GMC 1500 351V6 NP435
 

Parting out what little is left of this truck, been sitting for 30 years. Casting # codes to 351 V6. Engine is does not turn. Has most assys. Carb, distributor Pulleys, starter etc. $100. NP435 4 speed 100% complete w bell housing clutch driveshaft etc. $100 Front suspension all there. All parts priced low just inquire your needs. Just want this stuff to get used not crushed.

Steve weim55 Colorado

Re: Parting Out ‘67 GMC 1500 351V6 NP435
 

Man, I wish I could get that 435!

Re: Parting Out ‘67 GMC 1500 351V6 NP435
 

Do you have the headlight bezels? I’d like to see some pics of them if you think they’re useable

Re: Parting Out ‘67 GMC 1500 351V6 NP435
 

Awfully tempting on the 351/435. Do you have the engine stands and transmission crossmember?

Re: Parting Out ‘67 GMC 1500 351V6 NP435
 

Any interior? Seat belts, gauge cluster, glovebox door, knobs. How about any fender emblems?

Re: Parting Out ‘67 GMC 1500 351V6 NP435
 

Truck was hit in the front and likely what took it out of service. No useable body parts whatsoever.

Steve weim55 Colorado

Re: Parting Out ‘67 GMC 1500 351V6 NP435
 

Everything is present but the alternator and air cleaner. Throttle linkage, clutch linkage, engine mounts, exhaust etc. All there and untouched. If it is something you would be interested in we could torch the frame behind the transmission and could take the entire assembly engine, trans, mounts, frame section etc. for $200.

Steve weim55 Colorado

Re: Parting Out ‘67 GMC 1500 351V6 NP435
 

The only useable interior item might be the dash cluster. Truck has been sitting for years w/ no drivers door so the face is certainly weathered a bit. Fawn interior, I’ll take a pic later this week and post for you.

Steve weim55 Colorado

Re: Parting Out ‘67 GMC 1500 351V6 NP435
 

Shipping cost would probably kill it but I could crate it and truck ship.

Steve weim55 Colorado

Re: Parting Out ‘67 GMC 1500 351V6 NP435
 

I’m interested in it. Could you hold onto it for a bit if I paid you for it? With all the covid over regulation going on down here Im not supposed to leave NM except for work, without the 2 week quarantine BS.

Re: Parting Out ‘67 GMC 1500 351V6 NP435
 

Picking up an engine/trans sounds like work to me!

Re: Parting Out ‘67 GMC 1500 351V6 NP435
 

I’m not in a big hurry, if this needed to wait until spring we could take care of it then.

Steve weim55 Colorado

Re: Parting Out ‘67 GMC 1500 351V6 NP435
 

Sounds good, give me a day or two to think about this. I need to see what parts are available for the V6 before I commit. I’ve always wanted one but don’t know a ton about them.

Re: Parting Out ‘67 GMC 1500 351V6 NP435
 

Truck has been sitting for decades with no front clip. Engine was covered for the duration but very poorly, I would expect rust damage for sure inside that engine upon disassembly. Think about it and let me know. Thanks

Steve weim55 Colorado

Re: Parting Out ‘67 GMC 1500 351V6 NP435
 

I'd be interested in parts off that engine if he passes.

Re: Parting Out ‘67 GMC 1500 351V6 NP435
 

Steve after thinking about it some, I think I will pass. I’d hate to get it back home and have the block or crank not be useable. Seems parts for them are around but not always readily available in some instances. Thanks for your time and honesty on it all.

Re: Parting Out ‘67 GMC 1500 351V6 NP435
 

Any luck with pics?

Re: Parting Out ‘67 GMC 1500 351V6 NP435
 

PM sent on parts requested, Thanks.

Re: Parting Out ‘67 GMC 1500 351V6 NP435
 

No problem, thanks for letting me know,

Steve weim55 Colorado

Re: Parting Out ‘67 GMC 1500 351V6 NP435
 

Forgot to ask if you were looking for a three hole or seven hole.....

Steve weim55 Colorado

Re: Parting Out ‘67 GMC 1500 351V6 NP435
 

How good is the cab? Looks nice from what i can see. The cluster isn't quite what i am after. Any fender emblems? Thanks.

Re: Parting Out ‘67 GMC 1500 351V6 NP435
 

The only reason I purchased the truck was for the cab. It’s exceptionally nice, never ceases to amaze me how sometimes a beat up old work truck can somehow escaped the tin worm. The fenders were missing when I purchased it so unfortunately I have no outside pieces whatsoever. Thanks anyways,

Steve weim55 Colorado

Re: Parting Out ‘67 GMC 1500 351V6 NP435
 

What are you asking for the cluster?

Re: Parting Out ‘67 GMC 1500 351V6 NP435
 

$40 plus shipping

Steve weim55 Colorado

Re: Parting Out ‘67 GMC 1500 351V6 NP435
 

Steve, the package arrived safely and was obvious packaged with care!

Thank you again for making those engine parts available to me...

:gmc2: