The 1947 - Present Chevrolet & GMC Truck Message Board Network

The 1947 - Present Chevrolet & GMC Truck Message Board Network (https://67-72chevytrucks.com/vboard/index.php)
-   The 1967 - 1972 Chevrolet & GMC Pickups Message Board (https://67-72chevytrucks.com/vboard/forumdisplay.php?f=3)
-   -   69 C10 Steering Column (https://67-72chevytrucks.com/vboard/showthread.php?t=507021)

deathlinx 02-03-2012 04:23 PM

69 C10 Steering Column
 
i have a 69 C10. i want to remove the steering column to do some restorations. but i am currently un sure how to do so. if there is anyone that could provide me with instructions of how to do this it would help out my weekend a lot.


thank you

no moa 02-03-2012 04:36 PM

Re: 69 C10 Steering Column
 
Disconnect the column from the steering shaft, i just removed the bolt at the upper joint, and hammered it off, it comes off hard.

Remove the pin holding the shift rod to the column (assuming its an auto)

Remove the screws and bolts holding the column to the dash, there is a plate with 2 phillips screws, then remove the 1/2 bolts from the bottom of the plate.

There are 2 1/2 bolts at an angle that need to be removed to drop the column.

There is a plate at the firewall that has 2 5/16 screws, remove those.

Unhook the wiring at the top of the column behind the dash, and at the bottom of the column at the firewall.

I think that is all, i removed mine from the same truck 69 396 yesterday.

I think thats all i did. Take it slow, dont force it (except the joint to seperate the column and the shaft) and keep the bolts together, took me less than a 1/2 hour.

deathlinx 02-03-2012 04:56 PM

Re: 69 C10 Steering Column
 
ok thank you i will take a look. i am/was confused cause when i looked into the engine comp at the steering rod and bolts there are 3 different bolts. 1 all by its self and 2 more just a little above it that are close together. im not sure of which bolt(s) you are refering to...i will upload picture in just a minute for better reference. and yes it is an auto and 396 just as yours. so i hope you understand what i am saying

deathlinx 02-03-2012 05:04 PM

Re: 69 C10 Steering Column
 
1 Attachment(s)
ok taking a closer look there are 5 bolts...they are circled in RED. which of these am i taking off and out to be able to pull the column out after i disconnect plug and undo the dash and firewall brackets

no moa 02-04-2012 11:14 AM

Re: 69 C10 Steering Column
 
i did the bottom one, where the splines slide into that joint on the end of the shaft. Soak the sheet out of it with PB blaster, it will help.

Jeromy93 05-31-2013 09:14 PM

Re: 69 C10 Steering Column
 
Quote:

Originally Posted by deathlinx (Post 5164359)
ok taking a closer look there are 5 bolts...they are circled in RED. which of these am i taking off and out to be able to pull the column out after i disconnect plug and undo the dash and firewall brackets

On the bottom of the picture what is that whole piece called?

SS Tim 05-31-2013 10:23 PM

Re: 69 C10 Steering Column
 
If you don't have them, download the service manuals here.
http://67-72chevytrucks.com/vboard/s...d.php?t=558016


All times are GMT -4. The time now is 03:43 AM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com