Re: C20/cummins 12 valve
 

I hit up a transmission shop in San Diego. Guy had one in stock. I’ll try to find the name.

Re: C20/cummins 12 valve
 

Awesome man, thanks!

Re: C20/cummins 12 valve
 

Is there a part number on it?

Re: C20/cummins 12 valve
 

Hope this helps you.
Let me try it this weekend to make sure it fits.

Attachment 1901945

Attachment 1901946

Attachment 1901947

Re: C20/cummins 12 valve
 

Wiring:

Would I need a voltage regulator for a cummins for the swap?
Which wires need to be connected to make this work?
Should I run the grid heater? Don't get cold in Texas.
On the 68 I have the following for the alternator.
Red
White
Blue
Black
On the starter side I have the following.
Purple
Black
Yellow

On the cummins I have the following on the alternator:
Big black
Green
Blue

Don't have anything for the starter or the injection pump/shutoff solenoid.

Attachment 1901956

Attachment 1901957

Re: C20/cummins 12 valve
 

Alternator you can run a Mopar external voltage regulator as a stand alone Setup like the old school applications did, or like mine I used an internal regulator conversion and all I need is one keyed hot wire to the alternator and it puts out 14.4ish at the alternator at idle. Starter solenoid run your original purple wire to it, fuel shut off solenoid on the injection pump just needs a hot in start/run. I have my original ignition source feeding mine as it draws little current. Besides gauges I literally have 3 wires going to my engine.

Re: C20/cummins 12 valve
 

Starter and fuel shut off solenoid. I used my starter lug as my distribution block for my alternator, battery, and auxiliary take off to feed accessories and the cab, you can see the single purple solenoid wire. Shutoff solenoid is just a female spade terminal. My wiring is a little custom but the engine side will be the same. I planned on grid heaters hence the large gauge auxiliary wire coming off the starter, but in the low 20s mine still hit after just a couple seconds with a fuel heater delete also.

Re: C20/cummins 12 valve
 

The old school Mopar regulator made my lights “jump” a ford truck regulator will correct this

Re: C20/cummins 12 valve
 

Thanks, I’ll see what I can come up with.

Re: C20/cummins 12 valve
 

Found it! Lmk if it works and if you have the contact info please.

Thank you,
Jon

Re: C20/cummins 12 valve
 

Did you have a chance to install the mechanical speedometer drive?

Re: C20/cummins 12 valve
 

I was out of town for a few weeks but will be back on it this week.

Re: C20/cummins 12 valve
 

The vss screws into the part you bought and isn’t needed. I also bought one but could’ve just removed the vss and been done

Re: C20/cummins 12 valve
 

Sorry I couldn’t check it out for you “projectking”.
Little progress.

Attachment 1915154

Attachment 1915155

Attachment 1915156

Attachment 1915157

Re: C20/cummins 12 valve
 

All good. Nice progress!

Re: C20/cummins 12 valve
 

Little more.
Attachment 1915351

Re: C20/cummins 12 valve
 

Not good.
Attachment 1918872
Figured out why I couldn’t get it running.
Hopefully it’s not expensive.
“Chrome lever”

Re: C20/cummins 12 valve
 

That’ll do it for sure. If you decide to tear it down and fix it yourself I have a couple spare fulcrum assemblies. There are different numbers from the factory but I honestly don’t have a clue the difference. I remember one of the numbers being more prone to breaking and researched it when I built my pump but can’t rememeber which one I used. Future thought Incase you broke it putting the top back on, I usually back the power screw all the way out and then use a 6mm 1/4” drive with a swivel and extensions to get past the fuel lines to run it back in. I know it’s not a proper place to “sale” but if you need one I’ll send you one for $10 when it’s time.

Be warned it is easy to mess up and destroy internal pump parts if you don’t put things back in just right and then you’ll be looking for more parts or another pump. I’ll admit my first time I broke my rotor and since then always know for sure it’s all just right before install.

Re: C20/cummins 12 valve
 

Hydro boost
Will this work for me? Gmc van
Attachment 1956352

Attachment 1956354

Re: C20/cummins 12 valve
 

Don’t think so with that combination and your intake pipe. I moved my intake forward using a 24v plenum plate. Are you just wanting the better stopping power or is the vacuum pump not working?

Re: C20/cummins 12 valve
 

Need that stopping power.

Re: C20/cummins 12 valve
 

I was wondering if you ended up using this hydroboost setup? I have the same one on my truck. I am still looking for a different master cylinder. I was wondering if you ended up using a different master if so what did you use?

Re: C20/cummins 12 valve
 

Sorry hadn’t been on the site for a while. Moving and building a house and shop.

Re: C20/cummins 12 valve
 

It’s been a minute.
Got busy moving, building a house and shop.
Back to working on it.
Not sure about body work.
Might just get it blasted.
Attachment 2071227

Re: C20/cummins 12 valve
 

And the new shop.Attachment 2071219